
[Advanced]
176
3. Check the [Sensor] value.
If the value is 1.0 (V) higher than the "Low" level value you have recorded, this is the "High" level
value for the I-mark sensor.
If the difference between the "High" and the "Low" levels is less than 1.0, adjust the [Emit] and
[Receive] values so that the difference is more than 1.0, or adjust the "Low" level (voltage) of the I-
mark sensor again.
4. If both "High" and "Low" levels comply with the standard value, tap to confirm the value.
The standard values for the "High" and "Low" levels for the I-mark sensor are as follows:
◦
Low (without I-mark) < 0.5 (V)
◦
High (with I-mark) - Low ≥ 1.0 (V)
•
The changes to this setting are linked and are changed with the settings in the [Tools] >
[Media Startup] menu.
[I-Mark Slice Level]
Set the I-mark sensor slice level.
The setting procedure is as follows:
1. Use the following formula to calculate the slice level:
(High level - Low level) x 0.7 + Low level = slice level
2. Tap [I-Mark Slice Level] in the [Calibrate] menu.
3. Change the slice level value. Set the slice level to the slice level calculated in step 1.
4. Tap to confirm the value.
•
If you set the slice level to 0.0 (V), the product sets the slice level automatically.
•
The changes to this setting are linked and are changed with the settings in the [Tools] >
[Media Startup] menu.
[Head Check]
Automatically check if there is a broken element of the print head.
The options are as follows:
Off
Disable the head check.
All
Check the entire print area.
Barcode
Check only the area for printing a barcode. Head check is not applicable for barcodes printed as
graphic data.
Содержание CT4-LX
