
263
To stop the test print, pause printing, and then tap
.
The setting items are as follows:
Label Width
Shows the necessary media width of the test print.
The necessary media width is 101.6 mm (4") for [Large].
Pitch
Set the print position in the vertical direction.
The setting range varies depending on the print resolution of the product.
The setting range is as follows:
Resolution
Setting range
203 dpi (1 dot = 0.125 mm (0.0049"))
-30 to +30 dots
305 dpi (1 dot = 0.083 mm (0.0033"))
-45 to +45 dots
When you decrease the setting value, the print position moves in the feed direction.
When you increase the setting value, the print position moves opposite the feed direction.
Offset
Set the tear-off position/cut position/dispense stop position.
The setting range varies depending on the print resolution of the product.
The setting range is as follows:
Resolution
Setting range
203 dpi (1 dot = 0.125 mm (0.0049"))
-30 to +30 dots
305 dpi (1 dot = 0.083 mm (0.0033"))
-45 to +45 dots
When you decrease the setting value, the stop position moves in the feed direction.
When you increase the setting value, the stop position moves opposite the feed direction.
Darkness Adjust
Fine tune the print darkness of the test print.
0 is the lightest and 99 is the darkest.
•
You can change the units to dots, " (inches), or mm in the [System] > [Regional] >
[Unit] menu.
•
The changes to the settings in this menu are linked and are changed with each of the
test print settings under the [Test Print] menu.
•
The settings in [Pitch], [Offset], and [Darkness Adjust] are linked and are changed with
the settings in the [Printing] > [Advanced] > [Adjustments] menu.
Содержание CT4-LX
