
235
[Vert. Offset]
Specify the offset position in the vertical direction.
The setting range is from 0 to 400 dots.
•
The length of 1 dot varies depending on the print resolution of the product.
◦
203 dpi : 1 dot = 0.125 mm (0.0049")
◦
305 dpi : 1 dot = 0.083 mm (0.0033")
•
You can change the units to dots, " (inches), or mm in the [System] > [Regional] >
[Unit] menu.
[Label Rotation]
Set the page orientation for label printing.
The label size set in the product is used as a reference of rotation.
The options are as follows:
0 degree
Labels are printed in portrait orientation.
180 degree
Labels are printed in inverse-portrait orientation.
[Memory Device]
Select the product's memory space in which to store forms, graphics and fonts.
The options are as follows:
Internal RAM
Use the product's internal RAM. The data will be lost if the product is powered off.
Internal FLASH
Use the product's internal ROM.
Rear USB
Use the USB connector on the back of the product.
Internal USB
Use the internal USB connector.
•
Be sure to perform a virus check on the USB memory before connecting it to the
product. SATO Corporation shall not be held responsible for any product malfunctions
caused by a virus spread via USB memory.
[Sim. 300 DPI Head]
When you are using the product with 305 dpi resolution, enable or disable 300 dpi simulation mode.
Содержание CT4-LX
