SAF CFIP PhoeniX C Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 141

background image

28

CFIP PhoeniX C Series TDM/IP Split Mount System Technical Description and Configuration Guide

•

Rev. 1.0

•

© SAF Tehnika JSC 2013

Management and configuration examples of CFIP-16E1/T1-EXT

The configuration and status of the module can be found in web GUI in Ports/EMM management
menu:

EMM SUPPORT

This check box changes mode of SFP2 port from standard Gigabit ETH to proprietary EMM (Expansion)
mode. When EMM mode is enabled by this checkbox, IDU starts communication with all connected
EMM expansion modules.

EMM SETTING

–

EMM Type

- displays the type of connected EMM (Expansion) card.

-

N/A

- indicates that particular position is empty;

-

RELAY-IDU

- indicates that the relay IDU is connected directly to IDU SFP port (relay

application) or to EMM slave SFP port (add/drop configuration).

–

EMM Mode

– this function is related only to CFIP-16E1/T1-EXT module and allows to choose

traffic interface mode between E1 and T1

–

EMM Enable

– enables or disables generation/reception of data frames to/from Fiber Optic

stream. When enabled then particular EMM module occupies appropriate range of traffic port
channels

–

EMM Add/Drop ID

– specifies EMM Add/Drop Range – channel range which is in use by current

EMM module. In “auto” mode EMM module occupies port channel range according to its
position in EMM modules chain. In case of specific range of Add/Drop port channels, manual
Add/Drop ID setting is available as well.

–

EMM Add/Drop Range

– displays appropriate port channel range according to the EMM module

position and EMM Add/Drop ID setting.

Configuration menu of particular EMM (Expansion) module can be selected in dropdown box “EMM
selection”on the bottom of the EMM configuration page:

After selecting particular EMM module and pressing on “Change card without apply”, appropriate
EMM module’s configuration menu will be displayed:

«
...
26
27
28
29
30
...
»

Содержание CFIP PhoeniX C














































































































































Отзывы:

Нет отзывов

Похожие инструкции для CFIP PhoeniX C

Бренд: Samsung Страницы: 52

Бренд: Omega Altise Страницы: 16

Бренд: AAF Страницы: 4

Бренд: Carrier Страницы: 8

Intelli-Pro 3 XJ-3100A

Бренд: Surround Air Страницы: 8

Бренд: Hyundai Страницы: 40

Бренд: Orava Страницы: 115

Бренд: Daikin Страницы: 60

Бренд: Shark Страницы: 7

AIR COOLED CONDENSING UNIT 38EH

Бренд: Carrier Страницы: 6

Бренд: ShangFeng Страницы: 26

Бренд: Vaillant Страницы: 56

Бренд: Morgan Страницы: 6

VRV S RXQ4/5ARV1

Бренд: Daikin Страницы: 377

VRV X RXQ6-48ANR Series

Бренд: Daikin Страницы: 297

Бренд: Samsung Страницы: 55

Бренд: Samsung Страницы: 56

Бренд: Samsung Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды