SAF CFIP PhoeniX C Скачать руководство пользователя страница 29

Страница: 29 / 141

CFIP PhoeniX C Series TDM/IP Split Mount System Technical Description and Configuration Guide

•

Rev. 1.0

•

© SAF Tehnika JSC 2013

EMM CARD #x settings for CFIP-16E1/T1-EXP

Port/Channel Number

- a number of E1/T1 ports (channels), the number in red indicates alarm

status of appropriate internal channel (check alarm page for more details regarding this status)

Enable

– selects which E1/T1 ports are enabled for customer traffic connection.

Selecting/enabling of ports reserves appropriate capacity allocation from IDU for this type of
traffic even customer traffic is not carried (e.g. cable is disconnected) over any of enabled
channels.

Line Status

– displays the actual status of E1/T1 port or appropriate internal traffic channel

Termination

– displays the actual impedance matching of E1/T1 port

LLOOP

– local loopback configuration, incoming data stream from E1/T1 port is looped

RLOOP

– remote loopback configuration, receiving data stream from Fibre Optics is looped.

DLOOP

– dual loopback configuration, both data stream directions are looped inside the IDU

Coax Mode

– allows choosing E1/T1 interface mode (impedance) between standard 120 Ohm

balanced to 75 Ohm unbalanced. When enabled – 75 Ohms are selected. Chosen interface mode
is displayed in “Termination” row.

Technical specification of CFIP-E1/T1-EXT module

Traffic Interfaces

Item

Parameter

Value

CFIP-16E1/T1-EXT

Number of Ports

16 (16xRJ-45)

Interface

G.703-E1 balanced 120ohm for E1 mode
G.703-E1 unbalanced 75 ohm for E1 mode
T1.102-T1/100 ohm for T1 mode

Specification Compliance

T1.102, AT&T Pub 62411, T1.231, T1.403, ITU-
T G.703, G.742, G.775, G.823, ETS 300 166,
and ETS 300 233

Coding

HDB3 for E1 mode, B8ZS for T1 mode

Speed

2.048 Mbps for E1 mode, 1.554Mbps for T1
mode

Содержание CFIP PhoeniX C














































































































































Результаты поиска

Содержание CFIP PhoeniX C

Отзывы:

Бренды по названию

Популярные бренды

SAF CFIP PhoeniX C, Техническое описание

Результаты поиска

Содержание CFIP PhoeniX C

Отзывы:

Бренды по названию

Популярные бренды