SAF CFIP PhoeniX C Скачать руководство пользователя страница 119 | Manualshive

Страница: 119 / 141

SAF CFIP PhoeniX C Скачать руководство пользователя страница 119

119

CFIP PhoeniX C Series TDM/IP Split Mount System Technical Description and Configuration Guide

•

Rev. 1.0

•

© SAF Tehnika JSC 2013

Figure 104: Example 6 – Ports speed setting at LOCATION 2

Figure 105: Example 6 – SyncETH setting at LOCATION 2

The configuration of IDU 3 is similar to above explained GUI pages but with appropriate parameters
defined in Figure 101.

Example 7 – Basic 1+1 HSB/SD protection scheme

The  basic  1+1  protection  schemes  ensure  the  correct  data  transmission  over  the  microwave  link  in
case  of  specific  HW  block  failure  or  receive  conditions  degradation.(multipath  fading,  ..).  The
1+1 / HSB (hot standby) protection mode protects against system HW failures (hitless protects against
ODU_Rx, IDU_RxAFE, with short data drop protects against ODU_Tx, IDU_TxAFE). The 1+1 / SD (space
diversity)  protects  moreover  against  multipath  fading.  1+1 / HSB  mode  uses  usually  one  antenna
assembled by directional coupler, two ODUs are connected into this coupler. The 1+1 / SD mode uses
two antennas separated by specific distance with just one ODU connected into each antenna. Just one
transmitter is active in such  protection schemes (second one is automatically muted).  Two receivers
receive  the  identical  signal  and  master  IDU  decides  what  stream  will  be  used  for  final  data
demultiplexing.  The  basic  software  difference  between  HSB  and  SD  mode  is  that  in  SD  mode  with

«
...
117
118
119
120
121
...
»

Содержание CFIP PhoeniX C














































































































































Отзывы:

Нет отзывов