SAF CFIP PhoeniX C Скачать руководство пользователя страница 35

Страница: 35 / 141

CFIP PhoeniX C Series TDM/IP Split Mount System Technical Description and Configuration Guide

•

Rev. 1.0

•

© SAF Tehnika JSC 2013

EMM CARD #x settings for CFIP-ASI-EXP

Port/Channel Number

- a number of ASI ports (channels)

Enable

– selects which ASI ports are enabled for DVB ASI connection. The necessary link capacity

is automatically allocated according to sum of all ASI Rx streams.

Link Status

– displays the actual status of ASI port:

Status indications in case if

Rx mode

is set

- a valid ASI signal is present at appropriate input port

- a valid ASI signal is present at appropriate input port, but the port is not enabled for

traffic application

Idle

- ASI signal detected and successfully synchronized, but the signal does not contain

user data (MPEG stream is missing)

Idle

- ASI signal detected and successfully synchronized but the signal does not contain

user data (MPEG stream is missing) and the particular port is not enabled for traffic
application

nosync

- indicates that synchronization was not established for current received ASI signal

nosync

- indicates that synchronization was not established for current received ASI signal

and the port is not enabled for traffic application

loss

- no signal detected at ASI input port

loss

- no signal detected at ASI input port and the port is not enabled for traffic

application

Status indications in case if

Tx mode

is set:

- a valid inbound signal is present and transmitted via appropriate ASI port

- a valid inbound signal is present, but the port is not enabled for transmitting

Idle

- ASI signal detected and successfully synchronized but the signal does not contain

user data (MPEG stream is missing)

Idle

- ASI signal detected and successfully synchronized but the signal does not contain

user data (MPEG stream is missing), and the particular port is not enabled for traffic
application

Mode

– specifies if the particular port operates in Rx (ingress from coaxial cable) or Tx (egress to

coaxial cable) mode

Data Source

– specifies source for Tx signal. Either remote ASI port (Remote CH1-4) or one of

available local ASI Rx port (Local Ch1-4) can be chosen. This setting is available in Tx mode only

Содержание CFIP PhoeniX C














































































































































Результаты поиска

Содержание CFIP PhoeniX C

Отзывы:

Похожие инструкции для CFIP PhoeniX C

Бренды по названию

Популярные бренды

SAF CFIP PhoeniX C, Техническое описание

Результаты поиска

Содержание CFIP PhoeniX C

Отзывы:

Похожие инструкции для CFIP PhoeniX C

Бренды по названию

Популярные бренды