SAF CFIP PhoeniX C Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 141

SAF CFIP PhoeniX C Скачать руководство пользователя страница 50

50

CFIP PhoeniX C Series TDM/IP Split Mount System Technical Description and Configuration Guide

•

Rev. 1.0

•

© SAF Tehnika JSC 2013

PC setup with LAN adapter

In the case you are using management Ethernet cable for initial configuration you must first set your
computer IP address from the range which corresponds to the default IDU factory setup. By default
each IDU has from the factory the same IP address for ETH port (secondary IP address).

Default IDU ETH IP settings

IP address 10.10.10.10, net-mask 255.255.255.0

Therefore it is necessary to set the PC address in the range of 10.10.10.1-254, except for the device
own IP address (10.10.10.10). We recommend to set the computer as follows:

Computer LAN adapter settings

IP address 10.10.10.1, net-mask 255.255.255.0

Follow with the next step described in the figure below for computer IP settings.

Figure 29: PC IP LAN setup – local network connection

«
...
48
49
50
51
52
...
»

Содержание CFIP PhoeniX C














































































































































Отзывы:

Нет отзывов