SAF CFIP PhoeniX C Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 141

SAF CFIP PhoeniX C Скачать руководство пользователя страница 6

6

CFIP PhoeniX C Series TDM/IP Split Mount System Technical Description and Configuration Guide

•

Rev. 1.0

•

© SAF Tehnika JSC 2013

Chapter 2 – Technical Description

Introduction

Digital  microwave  system  CFIP  Phoenix  C  is  designed  in  split  mount  version,  the  IDU - ODU
architecture. There is only one universal IDU hardware version available with bandwidth up to 60 MHz
and applicable maximal output power. The indoor unit (CFIP Phoenix C IDU) is universal with respect
to  ETSI  and  ANSI  bandwidth  standards  and  universal  for  all  frequency  bands,  and  its  configuration
then depends on the loaded  software license key.  The outdoor units are unique  for  each frequency
band and sub-band.

System description

Signal  received  by  parabolic  antenna  is  carried  via  a  waveguide  adapter  to  the  receiving  filter  in
outdoor  unit.  The  task  of  outdoor  unit  (ODU)  is  to  convert  the  frequency  of  received/transmitted
signal to/from IF. The resulting converted signal is  together with management channel carried via the
coaxial  cable  to  the  CFIP  Phoenix  C  indoor  unit  (IDU).    The  signal  is  demodulated  inside  the  IDU,
followed by recovery of user data and management data intended for communication with ODU. As a
source  of  user  data  can  be  used  a  signal  for/from  the  Gigabit  Ethernet  ports  or  EMM  modules
connected  over  SFP  module.  Data  for  the  transmission  are  processed  similarly  in  the  reverse  order
than the received signal.

The CFIP Phoenix C system is technically characterized by the following basic features.

–

Standard licensed ETSI and ANSI frequency bands

–

Modulation schemes:

-

QPSK, 8 PSK, 16/32/64/128/256 QAM

–

Channel bandwidth

-

ETSI standards 7/14/27.5/28/40 and 56 MHz

-

ANSI standards 10/20/25/30/40/50 and 60 MHz

–

LDPC based Forward Error Correction

–

Hitless Adaptive modulation (ACM)

–

Four basic design modes (SW setting / License Key)

-

SINGLE – one data stream over air

-

MULTI – up to four independent data streams over air

-

AGGREGATE – 2+0 configuration with true capacity doubling

-

PROTECTED – 1+0 configuration in HSB/SD/FD modification

–

Two functional options (SW setting / License Key)

-

AES128, AES256 – AES encryption for high system security

-

PTP1588 – option which ensure IEEE1588 support

–

Integrated traffic ports

-

3x Gigabit Ethernet ports (10/100/1000Base-T) for user data traffic and/or
management access

-

2x SFP slots for additional GIGE port extension, EMM module connection or IDU
interconnection (protection, aggregation)

–

Integrated management ports

-

USB-B – for separate IP management access

-

USB-A – configuration restoration and backup by means of USB Flash memory

–

SyncE support in each design mode

–

Integrated data verification system of received corrupted packets (CRC)

–

Integrated BER tester and measurement of the nature of received signal (MSE, modulation

«
...
4
5
6
7
8
...
»

Содержание CFIP PhoeniX C














































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды