RS PRO 917-6298 Скачать руководство пользователя страница 18

Страница: 18 / 221

IIT-2000/2010/5000/5010 Instruction Manual/English

05/08/2015 Version No. 001

Display

240 X 64 dot matrix display (LCD)

Function keys

The function keys correspond to the soft-keys directly above on

the main display.

Pass/Fail

indicators

PASS

FAIL

The PASS and FAIL indicators light up upon a

PASS or FAIL test result at the end of a manual

test or automatic test.

ESC key

ESC

The ESC key is used to exit out of a menu or

cancel a setting.

PAGE key

PAGE

The PAGE key is used to view automatic test

information and test results.

Directional

arrow keys

The directional arrow keys are used to navigate

menus and parameter settings.

READY

indicator

READY

The READY indicator is lit when the tester is

ready to begin testing. The STOP button is used

to put the tester into READY status.

TEST indicator

TEST

The TEST indicator is lit when a test is on. The

START button is used to put the tester into TEST

status.

Содержание 917-6298






























































































































































































































Результаты поиска

Содержание 917-6298

Отзывы:

Бренды по названию

Популярные бренды

RS PRO 917-6298, Инструкция по эксплуатации

Результаты поиска

Содержание 917-6298

Отзывы:

Бренды по названию

Популярные бренды