4–14 • Advanced Operation
CrossOver 16 User Manual (v4.0)
7.
Press
NEXT
until
Option
is displayed.
8.
Use the
Option
knob to select
Invert Pan
.
9.
Use the
Value
knob to set whether the pan
axis is inverted. You can choose from the
following:
•
No
— The axis is not inverted. This is the
default value.
•
Yes
— The axis is inverted.
10.
Use the
Option
knob to select
Invert Tilt
.
11.
Use the
Value
knob to set whether the tilt
axis is inverted. You can choose from the
following:
•
No
— The axis is not inverted. This is the
default value.
•
Yes
— The axis is inverted.
AMP Protocol Devices
You can control devices that support the AMP
protocol. Currently, only the
play
command is
supported. Clips must be pre-loaded on the video
server.
Typically, the AMP device plays the clip when the
input it is assigned to is part of a transition. The clip
plays as soon as the transition starts, the switcher
waits for the defined pre-delay and then takes the
sources to air.
You can also issue the
play
command manually.
To manually play a clip:
1.
Select the input source that has been associated
with your video server.
2.
Press the
Play
knob to play the clip.
General Purpose Interface (GPI)
The switcher has 24 GPI inputs/outputs
corresponding to the pins on the GPI port. The GPI
inputs/outputs are arranged into 3 banks.
Figure 4.3 GPI Port
Banks configured as GPI inputs are used to trigger
memory recalls, transitions, and Aux bus input
changes.
Banks configured as GPI outputs allow your switcher
to trigger actions on external devices.
To configure GPI banks:
1.
Press
MENU
.
2.
Press the
CONFIG
Wipe Pattern button.
3.
Press the
GPIO
knob to display the
GPIO
menu.
4.
Use the
Bank
knob to select the GPI bank
you wish to configure.
5.
Use the
I/O
knob to select whether the bank
is configured as GPI inputs or outputs. You can
choose from the following:
•
GPO
— The bank is configured as GPI
outputs.
•
GPI
— The bank is configured as GPI inputs.
Note:
• Every pin in the selected bank initially goes low
when you change the bank from a GPI output to
GPI input.
GPI Output Banks
Banks configured as GPI outputs have output pins
assigned as follows (Pin 1 is the top right pin when
looking at the GPI Port).
Figure 4.4 GPI Port
To configure a GPI output bank:
1.
Press
MENU
.
2.
Press the
CONFIG
Wipe Pattern button.
3.
Press the
GPIO
knob to display the
GPIO
menu.
4.
Use the
Bank
knob to select a GPI bank
configured as GPI outputs.
5.
Press
NEXT
.
6.
Use the
Pin
knob to select which GPI output
pin to configure.
NEXT
13 12
11
10
9
8
7
6
5
4
3
2
1
14
15
16
17
18
19
20
21
22
23
24
25
MENU
13 12
11
10
9
8
7
6
5
4
3
2
1
14
15
16
17
18
19
20
21
22
23
24
25
MENU
NEXT
Содержание CrossOver 16
