Redline Communications RedMAX AN100U Скачать руководство пользователя страница 169

Страница: 169 / 178

Appendix D Synchronization Event Log Messages

D-5

Redline Communications Inc. Confidential and Proprietary

Slave

Synchronization Ok

Backup Detected

Master is offline, after rebooting.

Check the Master with GPS and
ensure it is online and that the GPS
is connected to the Master’s Sync In
port.

Verify that the synchronization
cables from the Master with GPS
and/or the Backup Master are
correctly connected to the Slaves’
Sync Out port.

Master

GPS is not Detected on the Master

No connection between the GPS and Master with GPS and the
Backup Master on Sync In or Sync Out port.

No corresponding event log messages are displayed by the Slave
devices.

Check the wiring connections
between Master with GPS and
Backup Master, check the
connection to the GPS unit.

Backup Master

Backup Function Activated

Master is not Detected

No connection between the GPS and Master with GPS and the
Backup Master on Sync In or Sync Out port.

You should see the above-listed messages on the Master.

No corresponding event log messages are displayed by the Slave
devices.

Check the wiring connections
between Master with GPS and the
Backup Master.

Also check the connections to the
GPS unit.

Master

GPS is not Detected

No connection between the GPS and the Master with GPS and
between the Master with GPS and Backup Master on the Sync In
port.

No corresponding event log messages are displayed by the Slave
devices.

Check the wiring connections
between the Master with GPS amd
the Backup Master.

Check the connection to the GPS
unit.

Table D-1

AN100U/UX Synchronization Event Log Messages (continued)

Message Reported
By

Event Log Message
(Logged starting from bottom to top)

Probable Cause

Recommended Troubleshooting

Содержание RedMAX AN100U



















































































































































































Результаты поиска

Содержание RedMAX AN100U

Отзывы:

Похожие инструкции для RedMAX AN100U

Бренды по названию

Популярные бренды

Redline Communications RedMAX AN100U, Руководство по администрированию и обслуживанию

Результаты поиска

Содержание RedMAX AN100U

Отзывы:

Похожие инструкции для RedMAX AN100U

Бренды по названию

Популярные бренды