Redline Communications RedMAX AN100U Скачать руководство пользователя страница 149 | Manualshive

Страница: 149 / 178

background image

C-3

Appendix C Subscriber Unit Event Log Messages

Redline Communications Inc. Confidential and Proprietary

Configuration restore failed

The restore operation failed.

You can retry the restore operation. Ensure you
have configured the correct FTP server for the
selected subscriber unit.

Ensure that there is connectivity with the sector
controller.

Ensure the software version that you are
restoring is compatible with the selected
subscriber unit.

Configuration restore
successful

The restore operation was successful. Information only. There is no action required.

Configuration save failed

An attempt to save the configuration of
this device encountered an error after
CLI/SNMP request.

Ensure you have configured the correct FTP
server for the selected subscriber unit.

Ensure that there is connectivity with the sector
controller.

Configuration save successful The configuration of the selected

device was saved successfully after a
CLI/SNMP request.

Information only. There is no action required.

Current BS connection lost.
Restart Initial Scan

The subscriber unit lost connection to
the last detected sector controller and
will restart a scan.

Information only. There is no action required.

Current BS connection lost.
Skip to next one

During the initial scan, the subscriber
unit lost connection to the last
detected sector controller and will try
registering with the next device on the
list of sector controllers to scan.

Information only. There is no action required.

Decode Certificate Done [nn]

The security certificate is ok.

Information only. There is no action required.

Decode Certificate Error

The security certificate that was
installed is invalid.

You need to update the security certificate on this
subscriber unit.

See the RedMAX AN100U/UX Base Station User
Guide.

Detected BS table empty.
Restart Initial Scan.

No sector controllers were detected
during the initial scan. The initial scan
is restarted.

Information only. There is no action required.

Detected BS table reset

The detected sector controller table
was reset either at the user’s request
or as result of changes to the RF
configuration.

Information only. There is no action required.

DCD Receiving Timeout

Five downlink channel descriptors in a
row have been expected and not
received. The subscriber unit will now
restart the ranging process in an
attempt to re-establish wireless
synchronization.

This message is normally a result of some
underlying RF problems.

Follow the steps detailed in the RF
troubleshooting section of this guide to resolve
this problem.

Table C-1

Subscriber Event Log Messages (continued)

Message

Description

Analysis

«
...
147
148
149
150
151
...
»

Содержание RedMAX AN100U



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RedMAX AN100U

BAKER HUGHES DPS 5000 Series

Бренд: GE Страницы: 36

Бренд: Oemtools Страницы: 8

Бренд: U.S. General Страницы: 5

Бренд: E-Mu Страницы: 52

Бренд: 2easy Страницы: 17

Бренд: 2DI Страницы: 38

Бренд: 2DI Страницы: 3

Бренд: ICC Страницы: 32

Бренд: Hama Страницы: 6

Бренд: Hama Страницы: 2

Бренд: Nailor Страницы: 6

Бренд: Talkswitch Страницы: 334

Бренд: Tait Страницы: 41

Бренд: Tait Страницы: 149

Бренд: Tait Страницы: 132

Бренд: Waterpik Страницы: 2

Бренд: Zamel Страницы: 12

6130N - Phaser Color Laser Printer

Бренд: Xerox Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды