Redline Communications RedMAX AN100U Скачать руководство пользователя страница 156 | Manualshive

Страница: 156 / 178

background image

C-10

Redline Management Suite Administration and Maintenance Guide

Redline Communications Inc. Confidential and Proprietary

No Maintenance Data Grant
Slot T4

If the subscriber has nothing to send,
the sector controller should grant
unsolicited bandwidth.

The subscriber unit should respond
with padding. This message indicates
that the sector controller has not
granted this data for 35 seconds.

This message indicates that sector controller
may have de-registered the subscriber unit due
to inactivity.

Non-buffered software
upgrade failed

A software upgrade, written directly to
flash due to lack of available RAM,
failed.

Reboot the subscriber unit, to minimize the
amount of memory fragmentation.

Non-buffered software
upgrade successful

A software upgrade, written directly to
flash due to lack of available RAM,
was completed successfully.

Information only. There is no action required.

Old Ksn nn, lifetime nn

This message provides information on
the status of your encryption key.

Information only. There is no action required.

When privacy is enabled, this is one of the many
steps that subscriber must perform to complete
the authentication process.

Overlapping UlMap IE
eliminated

Debug message. Error detected in
maps.

This could be the result of poor reception, RF
issues, interference. See “Troubleshooting
Wireless Link Issues” on page 5-18.

Provision: Corrupted Config
File

Error during TFTP self-provisioning

You need to correct and update the required
configuration file stored on the TFTP server.

You can manually configure the subscriber
through the sector controller or RMS.

Provision: Invalid Config Field
[nn]

Error during TFTP self-provisioning

You need to correct and update the required
configuration file stored on the TFTP server.

You can manually configure the subscriber
through the sector controller or RMS.

Provision: Invalid digest

TFTP self-provisioning error

You need to correct and update the required
configuration file stored on the TFTP server.

You can manually configure the subscriber
through the sector controller or RMS.

Provision: Invalid vendor ID

TFTP self-provisioning error

You need to correct and update the required
configuration file stored on the TFTP server.

You can manually configure the subscriber
through the sector controller or RMS.

Provision: Missing field id [nn] TFTP self-provisioning log

You need to correct and update the required
configuration file stored on the TFTP server.

You can manually configure the subscriber
through the sector controller or RMS.

Table C-1

Subscriber Event Log Messages (continued)

Message

Description

Analysis

«
...
154
155
156
157
158
...
»

Содержание RedMAX AN100U



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RedMAX AN100U

Бренд: D-Link Страницы: 2

BAKER HUGHES DPS 5000 Series

Бренд: GE Страницы: 36

Бренд: Oemtools Страницы: 8

Бренд: U.S. General Страницы: 5

Бренд: DAPU Страницы: 4

BOS R254K-UUI-LH10-S4

Бренд: Balluff Страницы: 196

Бренд: Hagan Страницы: 32

Бренд: Land Pride Страницы: 4

Бренд: Land Pride Страницы: 3

Instrument Control System

Бренд: Opus-Two Страницы: 8

scanCONTROL 25 100 Series

Бренд: MICRO-EPSILON Страницы: 60

Бренд: SR Suntour Страницы: 10

Бренд: Klarstein Страницы: 24

Бренд: SpectraLink Страницы: 14

Presence Sensor Air

Бренд: LOXONE Страницы: 2

Бренд: Yakima Страницы: 12

Бренд: APOLON Страницы: 19

E-Bike Frontlight E 80

Бренд: RFR Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды