Redline Communications RedMAX AN100U Скачать руководство пользователя страница 152 | Manualshive

Страница: 152 / 178

background image

C-6

Redline Management Suite Administration and Maintenance Guide

Redline Communications Inc. Confidential and Proprietary

DSX Action [error]

There has been an error in the
creation of a service flow. The
particular failure is detailed in the
message text.

Fundamental system problem, indicating
possible software incompatibilities, provisioning
bug etc. Likely to be caused by an interoperability
problem if a third party sector controller is used.

DSX Add Reject [reason]

This message signifies that the
addition of a service flow has been
rejected by the subscriber unit. The
reason for the failure is included in the
message text.

Possible reasons could include:

• a lack of system resources

• a specified parameter is not supported

• a required parameter is not provided

• a conflict with another provisioned service

• an error during the DSX transaction.

This message is only of concern if it happens
repeatedly.

Error decrypt key

System Error

Contact

[email protected]

Failed to acquire the
time-of-day

Communication with a ToD (RFC-868)
server has not been successful. The
correct time of day has not been
acquired. According to standard, the
subscriber unit must now perform a
MAC reboot and begin network entry
again.

This message implies that an IP address for the
ToD server has been successfully obtained from
a DHCP server, but that communication with said
ToD server has failed. Check network
connectivity between the ToD server and your
sector.

Finished Initial Scan.

The initial scan has been listed.
Another message will also be logged
to provide the status of the scan.

Information only. There is no action required.

Flash configuration updated

This message is the result of a restore
operation.

The system’s flash configuration was
updated and all settings have been
restored successfully.

Information only. There is no action required.

Flash parameters set to
default

This message is the result CLI/Web
client operation that changed specific
parameters.

The system’s flash configuration was
invalid at boot and has been reset to
the default.

Information only. There is no action required.

If system’s flash configuration was previously ok,
you may want to investigate further.

Flash parameters updated

Specific flash parameters have been
updated.

This message is the result CLI/Web
client operation that changed specific
parameters.

Information only. There is no action required.

FPC (nn) Current: [nn].
Anomaly: Too High

Fast power control (FPC) request log

Information only. There is no action required.

Table C-1

Subscriber Event Log Messages (continued)

Message

Description

Analysis

«
...
150
151
152
153
154
...
»

Содержание RedMAX AN100U



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RedMAX AN100U

Бренд: IFO Страницы: 12

Бренд: Bamo Страницы: 4

Jumbo MultiBigShoot

Бренд: agno's Страницы: 2

Бренд: Marantz Страницы: 2

Бренд: BAFANG Страницы: 12

Бренд: Trailboss Страницы: 5

Бренд: Stiebel Страницы: 23

ecoCRAFT VKK GB 1206/3-E-H

Бренд: Vaillant Страницы: 48

Бренд: Citiwell Страницы: 1

Бренд: JOBO Страницы: 9

ClickShare CSC-1

Бренд: Barco Страницы: 3

Бренд: Napoleon Страницы: 2

Бренд: Audi Страницы: 4

inView 360 Fusion

Бренд: Safe Fleet Страницы: 27

Бренд: ULTIMATE SPEED Страницы: 6

Cinema Mirror HC 37.53

Бренд: AVR Страницы: 9

Бренд: Colzer Страницы: 8

Бренд: König Electronic Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды