Redline Communications RedMAX AN100U Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 178

background image

3-3

Chapter 3 Indoor Equipment Maintenance

Redline Communications Inc. Confidential and Proprietary

Note

The RPS can only be used for the AN100UX.

The RPS scans and sets the power outputs at power-on and following a detected failure
of a connected AN100UX. <

During this time you need to obtain a replacement device and configure it using the most
recent backup from the disabled device and then replace it within the network.

Replacing the Indoor Unit of the AN100U/UX

Note

This procedure is service impacting and should only be performed during a
scheduled maintenance window.

Step 1

If possible, perform a configuration backup from the disabled device. Refer to the RedMAX
AN100U/UX Base Station User Guide for detailed instructions.

Step 2

Power off the RPS and the disabled device.

Step 3

Unplug the primary power cable from the supply and then from the disabled device.

Step 4

Remove the device from the mounting rack, if applicable.

Step 5

Install the replacement device in the rack and connect the power cable from the RPS.

Step 6

Connect the primary power cable and then connect the other end to the power supply.

Step 7

If the device does not power up automatically, then turn it on.

Step 8

Verify the successful restart and correct operation. Review the event log to ensure the
correct radio type is listed.

Step 9

Verify that the software version of the new device is the same or higher than the disabled
device.

Step 10 Restore the configuration of the disabled device. Refer to the RedMAX AN100U/UX Base

Station User Guide for detailed instructions.

Step 11 Log into the Web client and navigate to Monitoring > Status. Review the Status page to

verify that the air interface is enabled and to ensure the sector controller is operating
normally.

Step 12 Navigate to Monitoring > SS Info and verify any subscriber units are registered as

expected.

Step 13 Verify the wireless interface configuration: Interface Configuration > Wireless Interface.

The subscriber units should re-connected as soon as the sector controller is powered up.
You can verify the other operating parameters as required.

«
...
33
34
35
36
37
...
»

Содержание RedMAX AN100U



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RedMAX AN100U

Бренд: D-Link Страницы: 2

Бренд: GARO Страницы: 23

Бренд: La Crosse Technology Страницы: 2

Бренд: La Crosse Technology Страницы: 2

Бренд: La Crosse Страницы: 2

Бренд: Lantus Страницы: 5

Бренд: yasuni Страницы: 11

Бренд: LAS Страницы: 44

Бренд: LAS Страницы: 24

Бренд: Pivot Страницы: 4

ETIQUETTE MEMOIRE M I740N

Бренд: Aastra Страницы: 1

Бренд: Larson Electronics Страницы: 2

Бренд: Hama Страницы: 75

Бренд: Velleman Страницы: 4

XtraComfortTM Seat Extrasport

Бренд: Necky Kayaks Страницы: 2

Бренд: Brodit Страницы: 2

Бренд: Bestop Страницы: 4

Бренд: Grandstream Networks Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды