Redline Communications RedMAX AN100U Скачать руководство пользователя страница 154 | Manualshive

Страница: 154 / 178

background image

C-8

Redline Management Suite Administration and Maintenance Guide

Redline Communications Inc. Confidential and Proprietary

Invalid MAC address

This message is displayed when the
MAC address of the subscriber unit
does not belong to Redline.

The system will not function in this
state.

This only happens when Redline software is
loaded onto a non-Redline subscriber unit. This
is not supported by Redline.

Invalid private key file

The installed security certificate is
invalid.

You need to update the security certificate on this
subscriber unit.

See the RedMAX AN100U/UX Base Station User
Guide.

Invalid private/public key.
Deactivate privacy

The installed security certificate is
invalid. Encryption has been
deactivated

You need to update the security certificate on this
subscriber unit.

See the RedMAX AN100U/UX Base Station User
Guide.

Large Time Adjustment
Received

An excessively large timing correction
has been sent by the sector controller.
This correction has not been applied,
though it has been acknowledged.

This is a problem with your sector controller. It is
possible that the sector controller is
mis-calculating the timing offset of your
subscriber unit’s uplink bursts. Try adjusting the
sector controller’s reference RSSI to minimize
the difference between the strongest and
weakest uplink RSSI.

Learn: Ack Add Host
SeqNum[nn]

These 7 messages are part of the host
learning sequence. As host devices
are being added or deleted, these
messages will be added to the event
log.

Normal operation. There is no action required.

Learn: Ack Del Host
SeqNum[nn]

Normal operation. There is no action required.

Learn: Add New Host[XXXX
XX:XX:XX:XX:XX:XX]

Normal operation. There is no action required.

Learn: Del Old Host[XXXX
XX:XX:XX:XX:XX:XX]

Normal operation. There is no action required.

Learn: Deregistered

Normal operation. There is no action required.

Learn: Prov LearnCtrl[nn]
NumOfHosts[nn]

Normal operation. There is no action required.

Learn: Registered to
BS[XXXX
XX:XX:XX:XX:XX:XX]

Normal operation. There is no action required.

Lost DL-MAP

The time since the last valid DL MAP
was received by the subscriber unit
has exceeded the timeout.

The subscriber unit will now begin the
ranging process in an attempt to
re-establish wireless synchronization.

This message is normally the result of some
underlying RF problems.

See “Troubleshooting Wireless Link Issues” on
page 5-18.

Table C-1

Subscriber Event Log Messages (continued)

Message

Description

Analysis

«
...
152
153
154
155
156
...
»

Содержание RedMAX AN100U



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RedMAX AN100U

Бренд: Bartington Страницы: 11

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: IAG Страницы: 3

Бренд: Würth Страницы: 2

Бренд: Anslut Страницы: 12

Бренд: Metra Electronics Страницы: 2

Бренд: Southern Enterprises Страницы: 4

Бренд: Ohlins Страницы: 8

Бренд: media-tech Страницы: 13

Бренд: matev Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды