Raypak Xfiire 1000B Скачать руководство пользователя страница 20

Страница: 20 / 72

Mode 3

This mode selection is for hydronic heating systems with

single or multiple heaters (maximum 4 heaters) in primary/

secondary piping configuration with or without Outdoor

Air Reset (S4) with indirect DHW on the heater loop (with

priority). See

Figure 21.

The system temperature is controlled by the Supply Sensor

(S3) whenever the indirect call for heat is

not active. The

DHW Supply Sensor (S5) determines the indirect call/tank

setpoint. During an indirect call for heat the heater firing

rate is determined by the water temperature at the Indirect

Supply Sensor (S6) and the Target Max setting when using

the Indirect DHW sensor (S5).
The Heater/Injection Pump (P1) runs during all heat calls

regardless of priority. The Indirect DHW Pump (P3) runs

during an indirect call for heat with no “Off” delay.

Figure 21.

Mode 3 - Single Heater with Indirect on Heater Loop Primary/Secondary Piping

The Heater/Injection Pump (P1) is delayed “Off” as user-

defined in the Heater menu and the System Pump (P2) is

delayed “Off” in the ADJUST menu.
The System Pump (P2) runs whenever the system is

enabled for heating and the outdoor air temperature

is lower than the warm weather shut down (WWSD)

temperature setting (if utilized) unless an indirect call for

heat is present.

NOTE:

A Tank Aquastat can be used in lieu of the Indirect

DHW Sensor (S5). See VERSA IC Manual (5000.72) for

additional details.

NOTE:

See VERSA IC Manual (5000.72) for more

information on cascade systems.

VERSA

PIM

MODBUS

ENABLE

0-10/4-20mA

AQUASTAT

LOCATED IN

OUTLET PIPE

Maximum distance not to exceed

4 pipe diameters or 12" (305 mm)

FACTORY INSTALLED SENSOR
FIELD INSTALLED SENSOR

S1a

S2a

P2a

S3a

S1b

S2b

P1b

S1c

S2c

P1c

S1d

S2d

P1d

S4a

= FACTORY INSTALLED SENSOR
= FIELD INSTALLED SENSOR

(MASTER)

PIM

VERSA

PIM

VERSA

PIM

VERSA

PIM

VERSA

P1a

S5a

P3a

S6a

MODBUS

0-10/4-20mA

ENABLE

AQUASTAT

LOCATED IN

OUTLET PIPE

CONNECT SYSTEM

PUMP IN PARALLEL

FROM EACH CASCADE

FOLLOWER OUTPUT

Maximum distance not to exceed

4 pipe diameters or 12" (305 mm)

F10629

Figure 22.

Mode 3 - Heater Cascade with Indirect on Heater Loop Primary/Secondary Piping

Содержание Xfiire 1000B









































































Результаты поиска

Содержание Xfiire 1000B

Отзывы:

Похожие инструкции для Xfiire 1000B

Бренды по названию

Популярные бренды

Raypak Xfiire 1000B, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Xfiire 1000B

Отзывы:

Похожие инструкции для Xfiire 1000B

Бренды по названию

Популярные бренды