Raypak Xfiire 1000B Скачать руководство пользователя страница 17

Страница: 17 / 72

Figure 16.

Hydronic Primary/Secondary Piping

Mode 1

This mode selection is for hydronic heating systems with

single or multiple heaters (maximum 4 heaters) in primary/

secondary piping configuration with or without Outdoor Air

Reset (S4).

See

Figure 16

and

Figure 17

The system temperature is controlled by the System

Sensor (S3). The Heater Pump (P1) runs during any

call for heat. The System Pump (P2) runs whenever

the system is enabled for heating and the outdoor air

temperature is lower than the warm weather shut down

(WWSD) temperature setting (if utilized).
The Heater Pump (P1) is delayed “Off” as user-defined in

the Heater menu and the System Pump (P2) is delayed

“Off” in the ADJUST menu.

NOTE:

In cascade configuration, the system pump and

DHW pump (if applicable) outputs from each cascade

member must be connected in parallel to activate the

system pump and DHW pump during “limp-along”

operation respectively. See VERSA IC Manual (5000.72)

for detailed information.

FROM SYSTEM

BOILER PUMP

ISOLATION VALVE

(TYP)

4 PIPE DIAMETERS

OR MAX 12" (305 mm)

MAX. 5' (1.5 m)

TO SYSTEM SENSOR

TO SYSTEM

PRV

(PIPE TO DRAIN)

F10591

Содержание Xfiire 1000B









































































Результаты поиска

Содержание Xfiire 1000B

Отзывы:

Похожие инструкции для Xfiire 1000B

Бренды по названию

Популярные бренды

Raypak Xfiire 1000B, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Xfiire 1000B

Отзывы:

Похожие инструкции для Xfiire 1000B

Бренды по названию

Популярные бренды