Raypak Xfiire 1000B Скачать руководство пользователя страница 45

Страница: 45 / 72

Control Devices

WARNING:

Installation, adjustment and service of

heater controls, including timing of various operating

functions, must be performed by a qualified installer,

service agency or the gas supplier. Failure to do so may

result in control damage, heater malfunction, property

damage, personal injury, or death.

WARNING:

Turn off the power to the heater before

installation, adjustment or service of any heater controls.

Failure to do so may result in board damage, heater

malfunction, property damage, personal injury, or death.

CAUTION:

This appliance has provisions to be

connected to more than one supply source. To reduce the

risk of electric shock, disconnect all such connections

before servicing.

CAUTION:

Risk of electric shock: More than one

disconnect switch may be required to de-energize the

equipment before servicing.

Motorized Isolation Valve (Shipped Loose)

Refer to

Figure 46

and

Figure 47.

The heater is equipped with a relay output to control an

isolation valve as follows:

• Heater output energized = Isolation valve CLOSED
• Heater output de-energized = Isolation valve OPEN

The operation above may be manually adjusted by

manually inverting the operation of the isolation valve and

using the opposite dry contact of the relay output.
24VAC supply voltage for the isolation valve actuation is

also available at the rear of the heater in the wiring box,

next to the isolation valve relay output.

PRV

(PIPE TO DRAIN)

MOTORIZED

ISOLATION

VALVE

ISOLATION

VALVE (TYP)

SYSTEM

F10633

Figure 45. Motorized Isolation Valve Installation

CAUTION:

Failure to set up the Isolation Valve

correctly may damage the heater/system pump causing

non-warrantable failures.

F10505

Figure 46. Motorized Isolation Valve

Variable-Speed Pump Signal

The XFiire products are equipped with an analog output

that is proportional to the firing rate of the heater. This

0-20mA signal is intended to be used for an external

Variable-Speed pump as part of a Primary/Secondary

piping system. See

Figure 47

This output can also be configured for 0 -10 VDC using

an appropriate resistor connected in parallel between the

output terminals. Easy access to the terminals can be

found at the rear of the unit in the wiring box. See

Figure 3.

Содержание Xfiire 1000B









































































Результаты поиска

Содержание Xfiire 1000B

Отзывы:

Похожие инструкции для Xfiire 1000B

Бренды по названию

Популярные бренды

Raypak Xfiire 1000B, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Xfiire 1000B

Отзывы:

Похожие инструкции для Xfiire 1000B

Бренды по названию

Популярные бренды