Raypak Xfiire 1000B Скачать руководство пользователя страница 21

Страница: 21 / 72

Automatic Chemical Feeders

All chemicals must be completely diluted into the water

before being circulated through the heater. High chemical

concentrations will result when the pump is not running

(e.g. overnight).

CAUTION:

Combustion air must not be contaminated

by corrosive chemical fumes which can damage the

heater and void warranty.

CAUTION:

High chemical concentrations from

feeders that are out of adjustment will cause rapid

corrosion to the heat exchanger. Such damage is not

covered under the warranty.

CAUTI

ON: Failure of a heat exchanger due to lime

scale build-up on the heating surface, low pH, or other

chemical imbalance is not covered under the warranty.

Gas Supply

DANGER:

Make sure the gas on which the heater will

operate is the same type as specified on the heater’s

rating plate.

CAUTION:

Fuel grades of other than HD-5 Propane or

Natural Gas (980-1080 BTU/ft

) will require adjustments,

please contact the factory.

A pounds-to-inches regulator of the lock-up type must be

installed to reduce the gas supply pressure if it is higher

than 10.5" WC for natural gas or 13" WC for propane gas.

This regulator should be installed following the regulator

manufacturers instructions refer to

Table M

for maximum

pipe lengths.

Gas Supply Connection

A manual shut-off valve located outside the heater jacket

is required to be field supplied.

CAUTION:

The heater must be disconnected from

the gas supply during any pressure testing of the gas

supply system at test pressures in excess of 1/2 psi

(3.45 kPa).

The heater must be isolated from the gas supply piping

system by closing the upstream manual shut-off valve

during any pressure testing of the gas supply piping

system at test pressures equal to or less than 1/2 psi

(3.45 kPa). Relieve test pressure in the gas supply line

prior to re-connecting the heater and its manual shut-off

valve to the gas supply line.

FAILURE TO FOLLOW THIS

PROCEDURE MAY DAMAGE THE GAS VALVE

. Over-

pressurized gas valves are not covered by warranty. The

heater and its gas connections shall be leak-tested before

placing the appliance in operation. Use soapy water for

leak test. DO NOT use an open flame.

F10660

GAS SUPPLY

CONNECTION

Figure 23. Gas Supply Connection

CAUTION:

Only sealant tape or a pipe compound

rated for use with natural and propane gases is

recommended. Apply sparingly only on male pipe ends,

leaving the two end threads bare.

MODEL

NO.

1-1/4" NPT

1-1/2" NPT

2" NPT

300B

45 (15)

150 (46)

175 (53)

550 (168)

350 (107)

1100 (335)

400B

25 (8)

80 (24)

100 (30)

375 (114)

200 (61)

650 (198)

500B

15 (5)

40 (12)

65 (20)

250 (76)

150 (46)

450 (137)

650B

40 (12

150 (46)

85 (26)

300 (91)

850 (259)

800B

30 (9)

90 (27)

60 (18)

200 (60)

600 (182)

1000B

20 (6)

50 (15)

40 (12)

150 (46)

125 (38)

450 (137)

N = Natural gas and P = Propane gas
Natural gas - 1,000 btu/ft

, 0.60 specific gravity at 0.5" W.C. pressure drop / Propane gas - 2,500 btu/ft

, 1.53 specific gravity at 0.6" W.C.

pressure drop

Lengths based on Sched 40 BIP - for other materials consult local codes
Elbows as 10 ft equivalent pipe length

Table M.

Gas Supply Piping (Sched 40 BIP) (ft./m)

Содержание Xfiire 1000B









































































Результаты поиска

Содержание Xfiire 1000B

Отзывы:

Похожие инструкции для Xfiire 1000B

Бренды по названию

Популярные бренды

Raypak Xfiire 1000B, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Xfiire 1000B

Отзывы:

Похожие инструкции для Xfiire 1000B

Бренды по названию

Популярные бренды