Raypak Xfiire 1000B Скачать руководство пользователя страница 63

Страница: 63 / 72

PIM LED Error Code Listing

Active errors detected are indicated by LED lights on the PIM.

Error Mode

LED Flash Code on PIM

Recommended Troubleshooting

Normal Operation Red LED OFF

ID Card Fault

Red LED Steady ON,

Green Power LED OFF

Check that the proper ID Card is securely connected. Perform a power and

system reset.

Internal Control

Fault

Red LED Steady ON

Perform a power and system reset. If the fault remains, replace the PIM

N/A

Red LED – 1 Flash

N/A

False Flame Error Red LED – 2 Flashes

Check for proper gas valve closure. Clean burner and electrodes

Ignition Lockout

Fault

Red LED – 3 Flashes

Check the gas supply. Check transformer. Check igniters. Check wiring.

Press reset button on PIM/membrane switch. Recycle power

Ignition Proving

Current Fault

Red LED – 4 Flashes

Check DSI element. Replace as necessary

Low Voltage Fault Red LED – 5 Flashes

Check the 24VAC input voltage – the voltage must be above 18.0VAC for

proper operation. Replace transformer as necessary

N/A

Red LED – 6 Flashes

N/A

Hi-Limit Fault

Red LED – 7 Flashes

Check for proper water flow. Check hi-limit setting and outlet sensor

Sensor Fault

Red LED – 8 Flashes

Check the VERSA IC for fault identification. Check sensor and wiring

N/A

Red LED – 9 Flashes

Check wiring at J8, pins 1 and 3 for loose or missing jumper

Water Pressure

Fault

Red LED – 10 Flashes

Check system piping for leaks. Check water pressure switch (if equipped)

and connections. Check wiring on PIM at J1, pins 6 and 7 for loose or

missing jumper

Blower Speed

Fault

Red LED – 11 Flashes

Verify the tachometer signal and the connections at terminals J10 on the

PIM. Confirm power to heater is at or above minimum required

N/A

Red LED – 12 Flashes

Check wiring on PIM at J1, pins 3 and 4 for loose or missing jumper

Hi-Temperature

Delta Fault

Red LED – 13 Flashes

Check pumps operation. Confirm proper water flow across heat exchanger

(Delta T)

Ft_bus

Communications

Fault

Red LED – 14 Flashes

Verify that the VERSA IC is connected and operating properly. C

heck the cable between the PIM and the VERSA IC

General limit

circuit fault

Red LED – 15 Flashes

Check the VERSA IC for fault indication and troubleshooting information

Table AE. PIM LED Error Codes

Содержание Xfiire 1000B









































































Результаты поиска

Содержание Xfiire 1000B

Отзывы:

Похожие инструкции для Xfiire 1000B

Бренды по названию

Популярные бренды

Raypak Xfiire 1000B, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Xfiire 1000B

Отзывы:

Похожие инструкции для Xfiire 1000B

Бренды по названию

Популярные бренды