Raypak Xfiire 1000B Скачать руководство пользователя страница 15

Страница: 15 / 72

4 PIPE DIA

NOT TO EXCEED

12 IN. (305 mm)

5 FT. (1.5 M)

MAX

NOT TO SCALE

DRYWELL

SYSTEM

SENSOR

THERMAL PASTE

NPT FITTING

SYSTEM

PIPING

TO BOILER

FROM BOILER

F10501

Figure 14.

System Sensor Installation on Primary/

Secondary Systems

5 FT. (1.5 M)

MAX.

NOT TO SCALE

F10500

BOILER 1

OUTLET

BOILER 2

OUTLET

COMMON

PIPING

Figure 15. System Sensor Installation on Cascade Primary

Systems

Hydronic Heating

Pump Selection

The heater is designed for up to 80ºF (27ºC) ΔT and

continuous return temperatures from 40°F to 190°F (4.4°C

to 88°C).

NOTE:

Higher return temperatures may limit the firing

rate when the maximum water temperature of 200°F

(93°C) is approached.

ODEL

Flow Values GPM (lpm)

Max Flow**

Min. Flow*

@100%

Min. Flow*

300B

400B

500B

650B

800B

1000B

* Minimum flow based on H

O as heating media. Medias other than

O may require higher minimum flow rates.

** Maximum flow based on 10° ΔT or 10.5 feet per second velocity,

whichever is less.

Table J. Flow Rate

NOTE:

For systems using glycol, see Table K below for

necessary pumping requirements.

PARAMETER

CORRECTION

Ethylene Glycol Concentration (%)

Capacity Factor

Multiplier

1.000 0.972 0.960 0.928 0.878

GPM Correction

Multiplier

1.000 1.040 1.055 1.100 1.150

See Glycol section on on page 44.

Table K. Glycol Correction Factors (Requires Optional

Flow Meter)

Feedwater Regulator

Raypak recommends that a feedwater regulator be in-

stalled and set at 12 psi (8.3 kPa) minimum pressure at

the highest point of the system. Install a check valve or

back flow device upstream of the regulator, with a manual

shut-off valve as required by local codes.

Piping

All high points should be vented. This heater, when

used in connection with a refrigeration system, must be

installed so that the chilled medium is piped in parallel with

the heater with appropriate valves to prevent the chilled

medium from entering the heater. The piping system of a

hot water heater connected to heating coils located in air-

handling units where they may be exposed to circulating

refrigerated air, must be equipped with flow-control valves

or other automatic means to prevent gravity circulation

of the heater water during the cooling cycle. It is highly

recommended that the piping be insulated.

Содержание Xfiire 1000B









































































Результаты поиска

Содержание Xfiire 1000B

Отзывы:

Похожие инструкции для Xfiire 1000B

Бренды по названию

Популярные бренды

Raypak Xfiire 1000B, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Xfiire 1000B

Отзывы:

Похожие инструкции для Xfiire 1000B

Бренды по названию

Популярные бренды