Raypak Xfiire 1000B Скачать руководство пользователя страница 58

Страница: 58 / 72

6. While in operation, check flow switch operation.
7.

Check the low gas pressure switch (if provided). (For

proper adjustment, use the attached manometers, if

available, to set pressure. The scales on the switch

are approximate only.) Low gas pressure switch (if

provided) must be set at 3" WC for natural gas and

propane gas.

8. Make sure that the high gas pressure switch is set to

3" WC for both natural gas and propane gas.

Finishing

Record all data on the “Start-up Checklist” located at the

back of this manual.
Disconnect the manometers and reconnect the cap on the

fan pressure tee and reinsert the sealing screws into the

bleedle valves.
Start-up is complete and the heater should be operating

properly.

Follow-Up

Safety checks must be recorded as performed.
Turn heater on. After main burner ignition:
1.  Check manometer for proper readings.
2.  Cycle heater several times and re-check readings.
3.  Remove all manometers and replace caps and

screws.

4. Check for gas leaks one more time.
5.

To prepare for possible "limp-along" operation (if

communication is ever lost between the VERSA and

the PIM), set the operator Set Point potentiometer

on the PIM (See

Figure 29

) to the desired target

setpoint.

Leak Test Procedure: Dual-Seat Gas Valve

Proper leak testing requires three pressure test points in

the gas train. Remove the upper front panel to access the

gas valve for this test. See

Figure 59.

Test point A is a bleedle valve located upstream of the

combination gas valve on the supply manifold.
Test point B is a bleedle valve located between the two

automatic gas valve seats.
Test point C is a bleedle valve located downstream of both

automatic gas valve seats and upstream of the manual

valve. See

Figure 62.

These tests are to be conducted with the electrical power

to the heater turned OFF.
1. Manually close the downstream leak test valve.
2. Open the bleedle valve at test point A and connect

a manometer to it. Verify that there is gas pressure

and that it is within the proper range (NOTE: must

not exceed 14" WC).

Number

Field

Output Action

SYS

System Pump relay turns on

DHW

DHW Pump relay turns on

PMP 1

System and Heater Pump relays turn on

CWP

CWP Proportional output

Boil 1

Ignite Heater Burner

Min 1

Hold Heater at Min Fire

Max 1

Ramp Heater to Max Fire and hold

Table AC. User Test Fields

• On the first press of the Hold/Skip button, the test step

is held and “HOLD” is flashed at 1Hz.

• On the second press of the Hold/Skip button, the test

step is incremented.

• If heater outlet temperature reaches the PIM Hi-

Limit, the heater will be ramped down to keep the

temperature in a safe range.

• Press of the Hold/Skip button from Heater Max will

End the User Test function.

•

CWP MUST be enabled (VERSA DIP #3) VALVE

must be functioning during USER TEST.

NOTE:

If USER TEST is performed with Cold Water

Protection enabled (VERSA DIP 3 = ON), allow valve or

VS pump test sequence to complete uninterrupted or a

fault condition may occur.

Toolbox

Max Heat

Monitor

Factory Diagnostic

User Test

START

OFF

Log File Size

0 hrs

Fire Rate

0 %

BTC/PIM SW

Versa XXX

BTC/PIM SW

PIM XXX

Software: RPTS

XXX

System Tools

Units

↑

↓

Sample count:

Defaults

Contact Info

Start

Hold / Skip

Stop

°F

Flow Rate GPM

0.0

Figure 61. Touchscreen Toolbox Menu

Safety Inspection

1. Check all thermostats and high limit settings.
2. During the following safety checks leave manometers

hooked up, check and record.

3. If other gas-fired appliances in the room are on the

same gas main, check all pressures on the XFiire

with all other equipment running.

4. Check thermostats for ON-OFF operation.
5. Check high limits for ON-OFF operation.

Содержание Xfiire 1000B









































































Результаты поиска

Содержание Xfiire 1000B

Отзывы:

Похожие инструкции для Xfiire 1000B

Бренды по названию

Популярные бренды

Raypak Xfiire 1000B, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Xfiire 1000B

Отзывы:

Похожие инструкции для Xfiire 1000B

Бренды по названию

Популярные бренды