Raypak Xfiire 1000B Скачать руководство пользователя страница 9

Страница: 9 / 72

NO MINIMUM

SERVICE CLEARANCE

REQUIRED

30" (762 MM) MIN.

SERVICE CLEARANCE

FRONT VIEW

24" (610 MM) MIN.

SERVICE CLEARANCE

TOP VIEW

F10563

Figure 7. Minimum Clearances from Combustible

Surfaces – Indoor and Outdoor Installations

Clearances

Indoor Installations

Heater Side

Minimum

Clearances from

Combustible

Surfaces

in. (mm)

Minimum Service

Clearance

in. (mm)

Floor *

Rear

24 (610)

Right Side

Left Side

Top

Front

Open

30 (762)

Vent

1 (25)

* DO NOT install on carpeting

Table G. Clearances - Indoor Installations

For ease of servicing, a clearance of at least 30" (762 mm)

in front, at least 24" (610 mm) on the rear. This will allow

the heater to be serviced in its installed location without

movement or removal of the heater.
Service clearances less than the minimum may require

removal of the heater to service either the heat exchanger

or the burner components. In either case, the heater must

be installed in a manner that will enable the heater to be

serviced without removing any structure around the heater.

Pallet Jack/Forklifting

The XFiire heaters are designed to be moved by pallet jack

or forklift (front side or either side).

Figure 8. Pallet Jack

Figure 9. Forklifting

Содержание Xfiire 1000B









































































Результаты поиска

Содержание Xfiire 1000B

Отзывы:

Похожие инструкции для Xfiire 1000B

Бренды по названию

Популярные бренды

Raypak Xfiire 1000B, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Xfiire 1000B

Отзывы:

Похожие инструкции для Xfiire 1000B

Бренды по названию

Популярные бренды