Raypak Xfiire 1000B Скачать руководство пользователя страница 64

Страница: 64 / 72

10. MAINTENANCE

Suggested Minimum

Maintenance Schedule

Regular service by a qualified service agency and

maintenance must be performed to ensure maximum

operating efficiency.
Daily and monthly maintenance as outlined below may be

performed by onsite maintenance staff.

Daily

1. Check that the area where the heater is installed is

free from combustible materials, gasoline, and other

flammable vapors and liquids.

2. Check for and remove any obstruction to the flow of

combustion or ventilation air to heater.

Monthly

1. Check for piping leaks around pumps, mixing valves,

relief valves, and other fittings. If found, repair at

once. DO NOT use petroleum-based stop-leak

compounds.

2. Visually inspect venting system for proper function,

deterioration or leakage.

3. Visually inspect for proper operation of the

condensate drain in the venting. If leaks are observed

repair at once.

4. Check air vents for leakage.

Yearly (Beginning of each Heating Season)

Schedule annual service by qualified service agency.
1. Visually check top of vent for soot. Call service

person to clean. Some sediment at bottom of vent

is normal.

2. Visually inspect venting system for proper function,

deterioration or leakage. Ensure that condensate

drain is inspected and ensure that condensate is

being directed to appropriate condensate treatment

system or drain, as required by local codes.

3. Check that area is free from combustible materials,

gasoline, and other flammable vapors and liquids.

4. Follow pre-start-up check in the Start-up section.
5. Check flame strength signal as noted on display

Remove and visually inspect the direct spark igniter

and sensor for damage, cracking or debris build-up.

6. Check operation of safety devices. Refer to

manufacturers’ instructions.

Follow oil-lubricating instructions on pump (if

required). Over-oiling will damage pump. Water-

lubricated circulators do not need oiling.

Water Sensor / Outdoor Sensor

Water Temperature

Resistance (ohms)

32°F (0°C)

32550

41°F (5°C)

25340

50°F (10°C)

19870

59°F (15°C)

15700

68°F (20°C)

12490

77°F (25°C)

10000

86°F (30°C)

8059

95°F (35°C)

6535

104°F (40°C)

5330

113°F (45°C)

4372

122°F (50°C)

3605

131°F (55°C)

2989

140°F (60°C)

2490

149°F (65°C)

2084

158°F (70°C)

1753

167°F (75°C)

1481

176°F (80°C)

1256

185°F (85°C)

1070

194°F (90°C)

915

203°F (95°C)

786

212°F (100°C)

667

Sensor Resistance Values

Table AF. Approximate Sensor Resistance Values

Содержание Xfiire 1000B









































































Результаты поиска

Содержание Xfiire 1000B

Отзывы:

Похожие инструкции для Xfiire 1000B

Бренды по названию

Популярные бренды

Raypak Xfiire 1000B, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Xfiire 1000B

Отзывы:

Похожие инструкции для Xfiire 1000B

Бренды по названию

Популярные бренды