Raypak Xfiire 1000B Скачать руководство пользователя страница 19

Страница: 19 / 72

Figure 19.

Mode 2 - Single Heater with Indirect on System Loop - Primary/Secondary Piping

VERSA

PIM

MODBUS

ENABLE

0-10/4-20mA

AQUASTAT

LOCATED IN

OUTLET PIPE

Maximum distance not to exceed

4 pipe diameters or 12" (305 mm)

FACTORY INSTALLED SENSOR
FIELD INSTALLED SENSOR

Mode 2

This mode selection is for hydronic heating systems with

single or multiple heaters (maximum 4 heaters) in primary/

secondary piping configuration with or without Outdoor Air

Reset (S4) with indirect DHW on the system loop (with or

without priority). The system temperature is controlled by

the System Sensor (S3). The Indirect DHW Sensor (S5)

determines the indirect call/tank setpoint. See

Figure 19.

The system temperature is boosted to Target Max when

using the Indirect DHW Sensor (S5) during an indirect call

for heat. Priority mode toggles off the System Pump (P2)

when an indirect call for heat is present. The Heater Pump

(P1) runs during any call for heat. The Indirect DHW Pump

(P3) runs during an indirect call for heat with no “Off” delay.

The Heater Pump (P1) is delayed “Off”

as user-defined in

the Heater menu and the System Pump (P2) is delayed

“Off” in the ADJUST menu. The System Pump (P2)

runs whenever the system is enabled for heating and

the outdoor air temperature is lower than the WWSD

temperature setting (if utilized) unless an indirect call for

heat is present with priority.

NOTE:

See VERSA IC Manual (5000.72) for more

information on cascade systems.

S1a

S2a

P2a

S3a

S1b

S2b

S1c

S2c

S1d

S2d

S4a

(MASTER)

PIM

VERSA

PIM

VERSA

PIM

VERSA

PIM

VERSA

V1a

MODBUS

0-10 VDC

ENABLE

V1b

V1c

V1d

CONNECT SYSTEM PUMP

CASCADE FOLLOWER

IN PARALLEL FROM EACH

OUTPUT

AQUASTAT

LOCATED IN
OUTLET PIPE

= FACTORY INSTALLED SENSOR
= FIELD INSTALLED SENSOR

Maximum distance not to exceed

4 pipe diameters or 12" (305 mm)

F10628

Figure 20.

Mode 2 - Heater Cascade with Indirect on System Loop - Primary/Secondary Piping

Содержание Xfiire 1000B









































































Результаты поиска

Содержание Xfiire 1000B

Отзывы:

Похожие инструкции для Xfiire 1000B

Бренды по названию

Популярные бренды

Raypak Xfiire 1000B, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Xfiire 1000B

Отзывы:

Похожие инструкции для Xfiire 1000B

Бренды по названию

Популярные бренды