Raypak Xfiire 1000B Скачать руководство пользователя страница 7

Страница: 7 / 72

Figure 4. Component Locations - Top View

TRANSFORMER

BOX

OUTLET

PLUMBING

INLET

PLUMBING

GAS VALVE

FLOW SWITCH CONDUIT

F10607

3. WATER TREATMENT

Before and during assembly, the system must be kept free

of impurities, construction dust, sand, copper dust, grease,

carbon deposits, etc., as well as welding flux residue. In

any of these instances, the old system must be rinsed with

clear water mixed with a highly concentrated rinse agent.
More generally, it is advised to implement any procedure

necessary to prevent or treat contamination.

Black oxide sludge (magnetite-Fe

) forms as a result of

continuous electrolytic corrosion in any system unprotected

by an inhibitor. Iron oxide (Fe

) (red oxide sludge) is

produced during oxygenation. Scale deposit is made

up of lime scale contained in most distributed water that

settles over the warmest surfaces of the system. Sludge

and scale do mix together and are the cause of the main

encountered field problems on heating installations.

The presence of these substances means that standard

precautions are not implemented. In this case, product

warranty cannot be applied.
The chemical compatibilitiy of several products for the

treatment of heating water equipment has been tested on

heat exchangers.
Raypak recommends the using of these corrosion inhibitors

in preventive and curative treatment for boilers.

Producers

Fernox

Sentinel

Sotin

ADEY

Inhibitors

Protector

F1 / Alphi 11

X100,

X500

Sotin

212

MC1+

Noise

reducer

X200

Universal

Cleaner

Restorer

X300

Sludge

remover

Protector F1

Cleaner F3

X400

Sotin

212

Antifreeze

Alphi 11

X500

Table B.

Corrosion/Scale Inhibitors and Recommended

Suppliers

Treatment Type

Preventitive

Curative

Protector F1

Cleaner F3

X100

X200

X300

X400

X500

Alphi 11

Sotin 212

MC1+

Table C. Treatment Type

Water Chemistry

Boiler

Water Temperature

41 to 212°F

pH (system contains aluminum parts)

7.5-8.5

pH (without aluminum parts)

7.5-9.5

Total Dissolved Solids (GPG)

3-9

Table D. Boiler Water Chemistry

Models

Water Hardness

4-12 GPG

Water Hardness

12-15 GPG*

WH7-300B

27.3GPM

36.7GPM

6.0-8.5

WH7-400B

27.3GPM

36.7GPM

WH7-500B

32.8GPM

44GPM

WH7-650B

43.7GPM

58.6GPM

WH7-800B

54.6GPM

73.3GPM

WH7-1000B

65.5GPM

88.0GPM

When water hardness is higher than 15 GPG, a softener shall be

used. Water hardness values for calcium carbonate.

Table E. Water Heater Minimum Flow Rate

Содержание Xfiire 1000B









































































Результаты поиска

Содержание Xfiire 1000B

Отзывы:

Похожие инструкции для Xfiire 1000B

Бренды по названию

Популярные бренды

Raypak Xfiire 1000B, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Xfiire 1000B

Отзывы:

Похожие инструкции для Xfiire 1000B

Бренды по названию

Популярные бренды