Raypak Xfiire 1000B Скачать руководство пользователя страница 46

Страница: 46 / 72

0 - 10 VDC

RS485

REAR WIRING

BOX

PUMP

CONTACTOR

(BY OTHERS)

24VAC

PUMP

POWER

SUPPLY

N G

RESISTOR

500 OHM

0.25 - 0.5 WATT

TACO VR VIRIDIAN PUMP

RELAY

+24V SET3 SET2 0 V SET1

ETHERNET

LED2 LED1

HOT

RET

Figure 47. VS Pump Wiring Diagram

Ignition Control Functions

When there is a call for heat, and all safeties are closed

and minimum flow rate detected, then the combustion air

blower starts to purge air from the combustion chamber.

After the pre-purge, the igniter is energized. The standard

ignition module will lock-out after failing to light 3 times

during a call for heat. To reset the lock-out, press and

release the RESET button located adjacent the user

interface. The control will automatically reset after 1 hour.

When in lock-out the control will run the blower through a

post-purge cycle.

The single-try ignition module (part of the CSD-1 option)

will attempt to light only one time before lock-out occurs.

To reset the lock-out, press and release the RESET button

located adjacent the user interface.

Turning off the power to the heater WILL NOT reset the

single-try ignition module.

NOTE:

Ignition modules are common for all XFiire model

sizes. However, model-specific operating parameters

are defined by their respective ID cards.

3-Position Rocker Switch

This heater is equipped with a 3-position rocker switch

located on the front control panel (adjacent the touchscreen

display).
The 3-positions of this switch are:

Right = OFF

Middle = IDLE

Left = RUN

When the switch is in the OFF position, there is power to

the control and the heater is not operational.

WARNING:

There is still live electricity inside the

heater - disconnect electrical supply to the heater before

servicing the heater.

When the switch is in the IDLE position, power is supplied

to the control to allow for review/adjustment of settings, but

the heater will not fire.

CAUTION:

The Enable/Disable signal may be

overridden when the VERSA control is configured for

MODBUS "TEMP" or "RATE". Disable MODBUS prior to

servicing the heater.

When the switch is in the RUN position, the heater is

enabled to operate based on the water temperature and

target temperature setpoint.

High Limit - Manual Reset

This heater is equipped with a fixed-setting manual reset

high limit temperature device as standard. It may also

have an additional optional adjustable manual reset high

temperature device.
The optional manual reset high limit is located inside the

cabinet on the upper right corner post. See

Figure 2.

STANDARD

(Fixed)

OPTIONAL

(Adjustable)

Figure 48. High Limit (Manual Reset) (MRHL)

Содержание Xfiire 1000B









































































Результаты поиска

Содержание Xfiire 1000B

Отзывы:

Похожие инструкции для Xfiire 1000B

Бренды по названию

Популярные бренды

Raypak Xfiire 1000B, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Xfiire 1000B

Отзывы:

Похожие инструкции для Xfiire 1000B

Бренды по названию

Популярные бренды