Raypak Xfiire 1000B Скачать руководство пользователя страница 8

Страница: 8 / 72

Figure 5. Single Anchor Hole Locations

Figure 6. Multiple Unit Anchor Hole Locations

4. INSTALLATION

Installation Codes

Installations must follow these codes:
• Local, state, provincial, and national codes, laws,

regulations and ordinances

• National Fuel Gas Code, ANSI Z223.1/NFPA 54 –

latest edition (NFGC)

• National Electrical Code, ANSI/NFPA 70 - latest

edition (NEC)

• Standard for Controls and Safety Devices for

Automatically Fired Heaters, ANSI/ASME CSD-1,

(CSD-1) when required

• For Canada only: CAN/CSA B149 Natural Gas and

Propane Installation Code and CSA C22.1 C.E.C.

Part 1 (C22.1)

Equipment Base

The heater should be mounted on a level, structurally

sound surface. Local code may require housekeeping pad.

The heater is approved for installation on a combustible

surface but must NEVER be installed on carpeting. Gas-

fueled equipment installed in enclosed parking garages

must be located at least 18" (457 mm) above the floor.

CAUTI

ON: This heater should be located in an area

where water leakage will not result in damage to the area

adjacent to the appliances or to the structure.

In addition, the heater shall be installed such that the gas

ignition system components are protected from water

(dripping, spraying, rain, etc.) during appliance operation

or service (circulator replacement, control replacement,

etc.).
If the heater needs to be secured to the ground, use the

hole pattern shown in

Figure 5

and

Figure 6

, following

local codes.

25.00 (635)

4X 0.75 (19)

SINGLE BOILER

ANCOR LOCATIONS

4X 0.75 (19)

MULTI-BOILER

ANCHOR LOCATIONS

1.00 (46)

22.68

(576)

3.32

(84)

4.57

(116)

F10608

25.00 (635)

4X 0.75 (19)

SINGLE BOILER

ANCOR LOCATIONS

4X 0.75 (19)

MULTI-BOILER

ANCHOR LOCATIONS

1.00 (46)

22.68

(576)

3.32

(84)

4.57

(116)

F10608

MODELS

in. (mm)

300B - 500B

35.33 (897)

650B - 800B

43.75 (111)

1000B

48.50 (1231

Table F. Anchor Hole Dimensions

Содержание Xfiire 1000B









































































Результаты поиска

Содержание Xfiire 1000B

Отзывы:

Похожие инструкции для Xfiire 1000B

Бренды по названию

Популярные бренды

Raypak Xfiire 1000B, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Xfiire 1000B

Отзывы:

Похожие инструкции для Xfiire 1000B

Бренды по названию

Популярные бренды