Raypak Xfiire 1000B Скачать руководство пользователя страница 34

Страница: 34 / 72

F10572

D-15

VENT TERMINAL

36" MIN

(914 mm)

INTAKE

ELBOW

12" MIN

(152 mm)

36" MIN

(914 mm)

TEST PORT

VENT DRAIN W/ TRAP

ROUTE TO CONDENSATE

TREATMENT OR

CONDENSATE PUMP

HEATER UNIT

12"

(305 mm)

Figure 32. Direct Vent–Vertical for Stainless Steel and

Polypropylene

NOTE:

While a condensate drain connection for the

vent system is required on all XFiire installations, the

drain can be accomplished in several different ways.

The figures in this section show the drain from the heat

exchanger, however, this can also be accomplished using

an additional inline collector for condensing stacks or an

additional inline vertical or horizontal collector available

from several of the listed vent manufacturers.

Combustion air supplied from outdoors must be free

of particulate and chemical contaminants. To avoid a

blocked flue condition, keep the vent cap clear of snow,

ice, leaves, debris, etc.
The approved flue direct vent cap must be installed in

accordance with its listing. See

Table Q

and

Table R

WARNING:

Mixing of different manufacturers

venting material is not permitted as this may create an

unsafe condition.

Horizontal Through-the-Wall and

Direct Vent - Horizontal - Stainless

Steel and Polypropylene

The XFiire heaters may be vented horizontally (either using

room air for combustion or ducted air for combustion) as

shown in the following figures. The air intake terminal may

be located in a different pressure zone (i.e. on different

walls) from the vent termination. See

Figure 34.

12"

(305 mm)

HEATER UNIT

SLOPE TOWARD

APPLIANCE

1" IN 4'

(25.4 mm IN 1.2 m)

D-15

VENT TERMINAL

TEST PORT

12" MIN

(305 mm)

12" MIN

(305 mm)

VENT DRAIN W/ TRAP

ROUTE TO CONDENSATE

TREATMENT OR

CONDENSATE PUMP

F10570

Figure 33. Horizontal Through-the-Wall Venting for SS and

Polypropylene

F10573

VENT DRAIN W/ TRAP

ROUTE TO CONDENSATE

TREATMENT OR
CONDENSATE PUMP

TEST PORT

CAT IV

VENT PIPE

D-15

VENT TERMINAL

24" MIN

(610 mm)

HEATER UNIT

Figure 34. Direct Vent-Horizontal for SS and

Polypropylene

CAUTION:

This venting system may require the

installation of supplemental condensate drains in the

vent piping per the vent manufacturer’s instructions.

Failure to install these condensate drains in the venting

system may cause a non-warrantable failure.

Содержание Xfiire 1000B









































































Результаты поиска

Содержание Xfiire 1000B

Отзывы:

Похожие инструкции для Xfiire 1000B

Бренды по названию

Популярные бренды

Raypak Xfiire 1000B, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Xfiire 1000B

Отзывы:

Похожие инструкции для Xfiire 1000B

Бренды по названию

Популярные бренды