Raypak Xfiire 1000B Скачать руководство пользователя страница 38

Страница: 38 / 72

The vent cap is not considered in the overall length of the

venting system.
The vent must be installed to prevent flue gas leakage.

Care must be taken during assembly to ensure that all

joints are sealed properly and are airtight. The vent must

be installed to prevent the potential accumulation of

condensate in the vent pipes. It is required that:

• The vent must be installed with a condensate drain

located in proximity to the heater as directed by the

vent manufacturer.

• The vent must be installed with a slight upward

slope of not less than 1/4" per foot of horizontal run

to the vent terminal.

Termination

The flue direct vent cap MUST be mounted on the exterior

of the building. The direct vent cap cannot be installed

in a well or below grade. The direct vent cap must be

installed at least 12" (305 mm) above ground level and

above normal snow levels. The approved horizontal, PVC/

CPVC flue direct vent cap that must be used is a Tee of

the same size as vent pipe. See

Figure 38

and

Figure

. The vent terminal must be located NO CLOSER than

12" (305 mm) off the wall.

Outdoor Installation

Heaters must not be installed outdoors in freezing climates.

Heaters installed outdoors must be vented with listed UV-

resistant vent material per the following instructions and

installed with the factory-supplied Outdoor Vent Kit. See

Table U.

A special vent cap is provided in accordance with

CSA requirements. This must be installed directly on the

vent pipe as illustrated in

Figure 40

Model No.

Outdoor Kit No.

300B - 500B

017754

650B - 1000B

017755

Table U. PVC and CPVC Outdoor Vent Kits

NOTE:

External support of outdoor venting is required

if the vent extends beyond the jacket top by more than

36" (914 mm).

The flue outlet is not designed to support the weight of

the vent system beyond 36" (914 mm) above the jacket

top. Supplemental support is required if the vent extend

beyond 36" (914 mm).

The Raypak Outdoor Vent Kits contain the following

components:

•  SS Adapter
•  SS Elbow
•  34in Straight SS Vent
•  Termination Tee

• Installation Instructions

Care must be taken when locating the heater outdoors,

because the flue gases discharged from the vent cap can

condense as they leave the cap. Improper location can

result in damage to adjacent structures or building finish.
For maximum efficiency and safety, the following

precautions must be observed:
1. When heaters are installed outdoors, they must

use the Outdoor Vent Kit that is available from the

manufacturer (

See

Table U

or sales order option

D-11). Follow instructions provided with kit for

installation.

2. Periodically check venting system. The heater’s

venting areas must never be obstructed in any

way and minimum clearances must be observed to

prevent restriction of combustion and ventilation air.

See

Table I.

Keep area clear and free of combustible

and flammable materials.

3. Do not locate adjacent to any window, door, walkway,

or gravity air intake. The vent must be located a

minimum of 4' (1.2 m) horizontally from such areas.

NOTE:

Condensate can freeze on the vent cap. Frozen

condensate on the vent cap can result in a blocked flue

condition.

4. Install above grade level.
5.

Vent terminal must be at least 3' (914 mm) above any

forced air inlet located within 10' (3 m).

6. Adjacent brick or masonry surfaces should be

protected with a rust-resistant sheet metal plate to

prevent staining/corrosion of the wall surfaces.

F10573

VENT DRAIN W/ TRAP

ROUTE TO CONDENSATE

TREATMENT OR
CONDENSATE PUMP

TEST PORT

CAT IV

VENT PIPE

D-15

VENT TERMINAL

24" MIN

(610 mm)

HEATER UNIT

Figure 40. Outdoor Installation

Содержание Xfiire 1000B









































































Результаты поиска

Содержание Xfiire 1000B

Отзывы:

Похожие инструкции для Xfiire 1000B

Бренды по названию

Популярные бренды

Raypak Xfiire 1000B, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Xfiire 1000B

Отзывы:

Похожие инструкции для Xfiire 1000B

Бренды по названию

Популярные бренды