Porsche 911 GT3 Cup MR Gen. II Скачать руководство пользователя страница 98

Страница: 98 / 120

Version V2, 08/2020

Porsche 911 GT3 Cup MR Gen.II

Home

Active LEDs

LED Colour and Mode

Distance [m]

Approach Speed [km/h]

Approach Side

Description

Upper Right LED—

Slow

Flashing Green

60 m

Moderate ≥ 10 km/h

Right

The system detects an approaching vehicle on the right side of the

vehicle at far distance with a moderate approach speed.

Upper Left LED—

Slow

Flashing Green

60 m

Moderate ≥ 10 km/h

Left

The system detects an approaching vehicle on the left side of the

vehicle at far distance with a moderate approach speed.

Both Upper Right LEDs—

Slow

Flashing Orange

40 m

Moderate ≥ 10 km/h

Right

The system detects an approaching vehicle on the right side of the

vehicle at medium distance with a moderate approach speed.

Both Upper Left LEDs—

Slow

Flashing Orange

40 m

Moderate ≥ 10 km/h

Left

The system detects an approaching vehicle on the left side of the

vehicle at medium distance with a moderate approach speed.

Both Upper Right LEDs—

Slow

Flashing Red

20 m

Moderate ≥ 10 km/h

Right

The system detects an approaching vehicle on the right side of the

vehicle at short distance with a moderate approach speed.

Both Upper Left LEDs—

Slow

Flashing Red

20 m

Moderate ≥ 10 km/h

Left

The system detects an approaching vehicle on the left side of the

vehicle at short distance with a moderate approach speed.

Upper Right LED—

Fast

Flashing Green

60 m

High ≥ 20km/h

Right

The system detects an approaching vehicle on the right side of the

vehicle at far distance with a high approach speed.

Upper Left LED—

Fast

Flashing Green

60 m

High ≥ 20km/h

Left

The system detects an approaching vehicle on the left side of the

vehicle at far distance with a high approach speed.

Both Upper Right LEDs—

Fast

Flashing Orange

40 m

High ≥ 20km/h

Right

The system detects an approaching vehicle on the right side of the

vehicle at moderate distance with a high approach speed.

Both Upper Left LEDs—

Fast

Flashing Orange

40 m

High ≥ 20km/h

Left

The system detects an approaching vehicle on the left side of the

vehicle at moderate distance with a high approach speed.

Both Upper Right LEDs—

Fast

Flashing Red

20 m

High ≥ 20km/h

Right

The system detects an approaching vehicle on the right side of the

vehicle at short distance with a high approach speed.

Both Upper Left LEDs—

Fast

Flashing Red

20 m

High ≥ 20km/h

Left

The system detects an approaching vehicle on the left side of the

vehicle at short distance with a high approach speed.

ELECTRICS | Intelligent Color Display (ICD)

Содержание 911 GT3 Cup MR Gen. II

























































































































Результаты поиска

Содержание 911 GT3 Cup MR Gen. II

Отзывы:

Бренды по названию

Популярные бренды

Porsche 911 GT3 Cup MR Gen. II, Техническое руководство

Результаты поиска

Содержание 911 GT3 Cup MR Gen. II

Отзывы:

Бренды по названию

Популярные бренды