Porsche 911 GT3 Cup MR Gen. II Скачать руководство пользователя страница 38

Страница: 38 / 120

Version V2, 08/2020

Porsche 911 GT3 Cup MR Gen.II

Home

SUSPENSION | Power steering

25 Nm

Tightening torques must be observed!

Loose connections and frayed connection lines are the main reasons

for failure of the power steering pump. Short circuits may damage the

ATTENTION

NOTE

The rubber pad must be placed in the holder underneath the power

steering pump.

NOTE

Both lines (pressure line and return line) must be checked for firm

seating and chafing before each event. Damaged lines must be re-

placed.

16 Nm

20 Nm

NOTE

The power steering pump's ventilation line must not be kinked. Check

the condition of this line regularly.

NOTE

The connections + 12Volt BATT and the ground connection for the

power steering pump should be checked for firm seating and chafing

as part of the normal vehicle inspection.

Loose connections and frayed connection lines are the main reasons

for failure of the power steering pump. Short circuits may damage the

ATTENTION

Further information on the steering system can be found in the 911

GT3 Cup Gen.II technical manual from Porsche AG.

ATTENTION

The operating pressure of the system is

96 bar

Содержание 911 GT3 Cup MR Gen. II

























































































































Результаты поиска

Содержание 911 GT3 Cup MR Gen. II

Отзывы:

Бренды по названию

Популярные бренды

Porsche 911 GT3 Cup MR Gen. II, Техническое руководство

Результаты поиска

Содержание 911 GT3 Cup MR Gen. II

Отзывы:

Бренды по названию

Популярные бренды