Porsche 911 GT3 Cup MR Gen. II Скачать руководство пользователя страница 102

Страница: 102 / 120

102

Version V2, 08/2020

Porsche 911 GT3 Cup MR Gen.II

Home

Lookup Tables

Tyre Pressure Setup (dash_p_target)

►

The desired air pressures (hot air pressures) for the tires on the front and rear axles can be entered

in the lookup tables in the

"dash_p_target"

tab.

To set the required hot

air pressure [bar] at the front, enter the value with one decimal place and

decimal point separators in Row 0

To set the required hot

air pressure [bar] at the rear, enter the value with one decimal place and

decimal point separators in Row 1

The default value for the front and rear axles is 1.9 bar

NOTE

The system will not accept value entered using a comma as the deci-

mal separator

NOTE

If the preset values are changed, the setup with the new values must

be transferred to the ICD using the

"Send Setup"

button. All data still

stored on the ICD will be lost when the changed setup is transferred!

NOTE

The built

in TPMS sensors learn automatically. The procedure can take

up to 120 seconds. The conditions necessary for learning are;



All sensors are recognised as being installed by the system



The vehicle speed is >60Km/h

NOTE

ELECTRICS | Intelligent Color Display (ICD)

Содержание 911 GT3 Cup MR Gen. II

























































































































Результаты поиска

Содержание 911 GT3 Cup MR Gen. II

Отзывы:

Бренды по названию

Популярные бренды

Porsche 911 GT3 Cup MR Gen. II, Техническое руководство

Результаты поиска

Содержание 911 GT3 Cup MR Gen. II

Отзывы:

Бренды по названию

Популярные бренды