Porsche 911 GT3 Cup MR Gen. II Скачать руководство пользователя страница 47

Страница: 47 / 120

Version V2, 08/2020

Porsche 911 GT3 Cup MR Gen.II

Home

BODY EXTERIOR | Front Bumper

5.3 Front Bumper

►

Weight

optimized front bumper made of fiber composite material (CFRP) with a central air inlet for

the cooling air for the central water radiator. The air inlet is provided with a protective grille. Two

smaller air inlets are positioned to the left and right of the central air inlet for the front brake cooling.

The front bumper is attached using four fastening screws in the lower

area.

The front bumper must clip into the corresponding brackets on the

fender.

The front bumper is finally fastened using AeroCatch quick

release

catches on the left and right.

NOTE

3,5 Nm

8 Nm

The air intakes should be free of dirt (leaves, pick

up) at all times to

ensure the most efficient cooling possible.

NOTE

Protective grids can be inserted into the openings brake cooling inlets.

NOTE

Содержание 911 GT3 Cup MR Gen. II

























































































































Результаты поиска

Содержание 911 GT3 Cup MR Gen. II

Отзывы:

Бренды по названию

Популярные бренды

Porsche 911 GT3 Cup MR Gen. II, Техническое руководство

Результаты поиска

Содержание 911 GT3 Cup MR Gen. II

Отзывы:

Бренды по названию

Популярные бренды