Porsche 911 GT3 Cup MR Gen. II Скачать руководство пользователя страница 18

Страница: 18 / 120

Version V2, 08/2020

Porsche 911 GT3 Cup MR Gen.II

Home

EXHAUST SYSTEM & FUEL SYSTEM | Silencers

3.3 Porsche Motorsport Silencers

NOTE

►

For events with strict noise requirements, the side silencers available from Porsche Motorsport can

be installed.

All components of the optionally available side silencers must be in-

stalled. Failure to observe can lead to heat build

up in sensitive areas.

Risk of fire!

Detailed installation instructions can be downloaded from the down-

load area of the Manthey Racing website.

WARNING

The components of the side silencers must be checked for damage

before each session. Rubber parts (pickup) must not accumulate on

the components. Risk of fire!

WARNING

The side brackets 9F0813651B and 9F0813652B must be cut on the

line shown opposite.

The side brackets are not part of the "front silencer" scope of delivery.

NOTE

Please note that all parts described in the technical manual of the 911

GT3 Cup Gen.II must be installed for the assembly of the side

silencers.

Содержание 911 GT3 Cup MR Gen. II

























































































































Результаты поиска

Содержание 911 GT3 Cup MR Gen. II

Отзывы:

Бренды по названию

Популярные бренды

Porsche 911 GT3 Cup MR Gen. II, Техническое руководство

Результаты поиска

Содержание 911 GT3 Cup MR Gen. II

Отзывы:

Бренды по названию

Популярные бренды