Porsche 911 GT3 Cup MR Gen. II Скачать руководство пользователя страница 104

Страница: 104 / 120

104

Version V2, 08/2020

Porsche 911 GT3 Cup MR Gen.II

Home

Lookup Tables

Light_Function_right

►

Similar to the settings of the

“Light_Functions_left”,

these settings for the LEDs of the right main

headlight can be adjusted via the

“Light_Functions_right”

tab.

If the preset values are changed, the setup with the new values must

be transferred to the ICD using the

"Send Setup"

button. All data still

stored on the ICD will be lost when the changed setup is transferred!

Carry out a data backup beforehand!

NOTE

Procedure for setting the Color ID / display of the Error Monitor when crossing the timing signal for

the LEDs of the left main headlight:



Enter in Row 0 the Value 1, if the Color ID should be displayed after crossing beacon signal



Enter in Row 0 the Value 2, if the Error Monitor should be displayed after crossing beacon signal

Procedure for setting the Color ID when the Pit Speed Limiter is active.



Enter in Row 1 the Value 1, if the Color ID is to be activated when the Pit Speed Limiter is acti-

vated (in the pitlane)

Open the tab

“Light_Function_right“

It is advisable to configure the LEDs of one headlight with the desired

Color ID and the LEDs of the other headlight to display of any error

entries (Alarms / Error Monitor).

NOTE

ELECTRICS | Intelligent Color Display (ICD)

The following alarms/errors can be displayed via the LEDs of the headlights when the

beacon signal is crossed. The display then takes place with red glowing LEDs. There is no

differentiation/specification of the alarm / error;



Alternator



Crankcase Pressure



Oil Level high



Oil level low



PCU



Fuel Pressure



Oil Pressure



Water Pressure



Gearbox Oil Temperature



Water Temperture



Oil Temperature



Battery Voltage



Water Level

Содержание 911 GT3 Cup MR Gen. II

























































































































Результаты поиска

Содержание 911 GT3 Cup MR Gen. II

Отзывы:

Бренды по названию

Популярные бренды

Porsche 911 GT3 Cup MR Gen. II, Техническое руководство

Результаты поиска

Содержание 911 GT3 Cup MR Gen. II

Отзывы:

Бренды по названию

Популярные бренды