Porsche 911 GT3 Cup MR Gen. II Скачать руководство пользователя страница 27

Страница: 27 / 120

Version V2, 08/2020

Porsche 911 GT3 Cup MR Gen.II

Home

SUSPENSION | Brake Cooling Front Axle

►

The brake ventilation on the front axle of the 911 GT3 Cup MR Gen.II has been significantly increa-

sed compared to the base vehicle. The cooling air flows to the brakes on the front axle via openings

in the front bumper.

4.3 Brake Cooling

Front Axle

NOTE

The flexible hose section is heavily stressed by the steering move-

ments while driving and is subject to increased wear. A visual inspec-

tion before each session is recommended. Defective hose sections

must be replaced immediately.

3 Nm

10 Nm

3 Nm

NOTE

Do not tighten the hose clamps with a higher torque as specified.

NOTE

Before each session, all components must be checked for unrestricted

air flow and damage.

NOTE

In order to prevent the brake system from over

cooling in races with

extremely long straights (e.g. Nordschleife), the brake vents should be

partially closed with suitable means (blanking plate). The target should

be to maintain the brake disc temperature at approx. 250

300°C in

order to guarantee optimal braking performance at all times and to

counteract the premature wear of the brake discs (cracking).

Содержание 911 GT3 Cup MR Gen. II

























































































































Результаты поиска

Содержание 911 GT3 Cup MR Gen. II

Отзывы:

Бренды по названию

Популярные бренды

Porsche 911 GT3 Cup MR Gen. II, Техническое руководство

Результаты поиска

Содержание 911 GT3 Cup MR Gen. II

Отзывы:

Бренды по названию

Популярные бренды