Porsche 911 GT3 Cup MR Gen. II Скачать руководство пользователя страница 111

Страница: 111 / 120

111

Version V2, 08/2020

Porsche 911 GT3 Cup MR Gen.II

Home

ELECTRICS | Traction Control

►

For the 911 GT3 Cup MR Gen.II, a traction control that can be set in 12 levels is optionally available.

The system can be set to 12 levels independently of ABS. Where "0"

means that the system is deactivated. Stage 12 means maximum

control interventions by the traction control.

6.5 Traction Control (TC)

NOTE

The "traction control" function is stored and programmed on the engi-

ne control unit. If the engine control unit is replaced, the "traction con-

trol" function is no longer available.

Programming is done exclusively by Manthey

Racing GmbH. The en-

gine control unit must be sent in for programming.

NOTE

If the control level of the traction control is adjusted via the rotary

selector switch, this change is displayed to the driver in the ICD for

approx. 2 seconds. Control interventions are visually signaled to the

driver via the LEDs on the side of the ICD. The upper LEDs flash purple

for the duration of the intervention.

NOTE

In addition to an appropriately programmed engine control unit, the

correct ICD setup is required for the correct functioning of the traction

control. This can only be ordered through Manthey

Racing GmbH and

is only available to customers with a 911 GT3 Cup MR Gen.II.

NOTE

The following componets are required for the use of the TC:



New dataset for the ECU



New ICD setup including TC function



Wiring loom with TC rotary switch

Содержание 911 GT3 Cup MR Gen. II

























































































































Результаты поиска

Содержание 911 GT3 Cup MR Gen. II

Отзывы:

Бренды по названию

Популярные бренды

Porsche 911 GT3 Cup MR Gen. II, Техническое руководство

Результаты поиска

Содержание 911 GT3 Cup MR Gen. II

Отзывы:

Бренды по названию

Популярные бренды