Porsche 911 GT3 Cup MR Gen. II Скачать руководство пользователя страница 42

Страница: 42 / 120

Version V2, 08/2020

Porsche 911 GT3 Cup MR Gen.II

Home

BODY EXTERIOR | Service Intervals

5.1 Service Intervals

Part

Service interval

Max. runtime

Service advice

Air jack system

Before every session

Check for leaks and damage to lines and
air jacks. Check that the lair jacks are
firmly seated in the body mounts. Check
the front air jack seats for firm seating
and cracks.

Air jacks

2,000 strokes / 2 years

Revision of the air jacks by the manufac-

turer. Check the jacks for damage every

time the vehicle is serviced and maintain

with silicone spray.

Lock pins

Before every session

Check for tightness and damage. Replace

if necessary.

Aerocatch fasteners and retaining tabs on

boot lid and front front covering

Before every session

Check for tightness and damage .Replace

if necessary.

Heat protection insulation

Before every session

Check the heat protection insulation on

the diffuser and rear panel for damage,

repair if necessary.

Fiber composite parts

Before every session

Visually inspect fiber composite compo-

nents for structural damage before each

session.

Содержание 911 GT3 Cup MR Gen. II

























































































































Результаты поиска

Содержание 911 GT3 Cup MR Gen. II

Отзывы:

Бренды по названию

Популярные бренды

Porsche 911 GT3 Cup MR Gen. II, Техническое руководство

Результаты поиска

Содержание 911 GT3 Cup MR Gen. II

Отзывы:

Бренды по названию

Популярные бренды