Porsche 911 GT3 Cup MR Gen. II Скачать руководство пользователя страница 17

Страница: 17 / 120

Version V2, 08/2020

Porsche 911 GT3 Cup MR Gen.II

Home

EXHAUST SYSTEM & FUEL SYTEM | Exhaust Manifolds

3.2 Exhaust Manifolds

NOTE

►

The exhaust manifolds of the 911 GT3 Cup MR Gen.II correspond to the standard exhaust ma-

nifolds. Due to the closed underbody on the 911 GT3 Cup MR Gen.II, cool air can no longer flow

around the exhaust manifold. In order to protect surrounding components from excessive heat ra-

diation / heat transfer, the exhaust manifolds have been equipped with a special heat protection

insulation.

Only exhaust manifolds with heat protection insulation may be driven

with. Failure to observe this may damage surrounding components

due to the effects of heat. Risk of fire!

Only new exhaust manifolds can be provided with the heat protection

insulation. New exhaust manifolds with heat protection must be obtai-

ned from Manthey

Racing GmbH.

35 Nm

WARNING

The heat protection insulation must be checked for damage before

each session. Rubber parts (pickup) must not accumulate on the ex-

haust manifolds. Risk of fire!

WARNING

The brackets including clamps of the 911 GT3 Cup MY 2016 must

NOT

be installed. This could damage the heat protection insulation.

NOTE

The specified tightening torque for the M8 fastening nuts for connec-

ting the manifold to the engine block must be observed. The metal

seals between the manifold and the engine block must be replaced

after each disassembly.

NOTE

The maximum runtime of the exhaust manifold described in the 911

GT3 Cup Gen.II manual remains unchanged.

Содержание 911 GT3 Cup MR Gen. II

























































































































Результаты поиска

Содержание 911 GT3 Cup MR Gen. II

Отзывы:

Бренды по названию

Популярные бренды

Porsche 911 GT3 Cup MR Gen. II, Техническое руководство

Результаты поиска

Содержание 911 GT3 Cup MR Gen. II

Отзывы:

Бренды по названию

Популярные бренды