Porsche 911 GT3 Cup MR Gen. II Скачать руководство пользователя страница 37

Страница: 37 / 120

Version V2, 08/2020

Porsche 911 GT3 Cup MR Gen.II

Home

SUSPENSION | Power Steering

►

On the 911 GT3 Cup MR Gen.II, the standard power steering pump of the 911 GT3 Cup Gen.II is

moved from the boot liner to the front area of the left wheel arch below the main headlight.

4.10 Power Steering

10 Nm

The holder for the power steering pump must be mounted horizontally

on the body. Failure to do so may result in the pump drawing air

during extreme driving maneuvers and causing the pump to fail tem-

porarily.

ATTENTION

Even small amounts of air in the system significantly reduce the ser-

vice life of the power streeing pump and the steering rack.

ATTENTION

NOTE

The protective housing around the power steering pump must be in-

stalled. Pump damage can occur otherwise (e.g. delaminating tyre).

Further information on the steering system can be found in the 911

GT3 Cup Gen.II technical manual from Porsche AG.

NOTE

Maintanence work, such as refilling the system after replacing the ste-

ering rack, is carried out in accordance with the technical manual for

the 911 GT3 Cup Gen.II from Porsche AG.

8 Nm

0°

6 Nm

10 Nm

NOTE

The fluid level in the reservoir can be checked and adjusted via the

service flap in the left fender (lamp housing).

Содержание 911 GT3 Cup MR Gen. II

























































































































Результаты поиска

Содержание 911 GT3 Cup MR Gen. II

Отзывы:

Бренды по названию

Популярные бренды

Porsche 911 GT3 Cup MR Gen. II, Техническое руководство

Результаты поиска

Содержание 911 GT3 Cup MR Gen. II

Отзывы:

Бренды по названию

Популярные бренды