Porsche 911 GT3 Cup MR Gen. II Скачать руководство пользователя страница 76

Страница: 76 / 120

Version V2, 08/2020

Porsche 911 GT3 Cup MR Gen.II

Home

ELECTRICS | Intelligent Color Display (ICD)

6.4 Intelligent Color Dis-

►

The ICD display pages available on the 911 GT3 Cup MR Gen. II are presented and described on the

following pages.

►

A total of seven view pages can be called up. The name of the respective page is shown in the lower

right area of the screen. The following display pages are available and can be changed using the
yellow "Display" steering wheel button.



Race



Quali



Warmup

(Not availaible while driving)



Vitals

(Not availaible while driving)



Controls

(Not availaible while driving)



Chassis

(Not availaible while driving)

Adjusting and operating the ICD while driving can distract from the
surrounding environment. Control of the vehicle can be lost.

Only operate the ICD while driving if the traffic conditions allow.

In addition to displaying information for the driver, the ICD takes on
numerous control and monitoring functions. Since the systems of the
911 GT3 Cup MR Gen. II are much more extensive than those of a
standard 911 GT3 Cup Gen. II, only Cup MR

specific ICD setups pro-

vided by Manthey

Racing GmbH may be used to operate the vehicle.

Failure to observe inevitably leads to malfunctions and failure of the

Due to the continual product optimization, the download area of Man-

they

Racing GmbH should be checked at regular intervals for any soft-

ware updates.

ATTENTION

WARNING

Содержание 911 GT3 Cup MR Gen. II

























































































































Результаты поиска

Содержание 911 GT3 Cup MR Gen. II

Отзывы:

Бренды по названию

Популярные бренды

Porsche 911 GT3 Cup MR Gen. II, Техническое руководство

Результаты поиска

Содержание 911 GT3 Cup MR Gen. II

Отзывы:

Бренды по названию

Популярные бренды