Porsche 911 GT3 Cup MR Gen. II Скачать руководство пользователя страница 103

Страница: 103 / 120

103

Version V2, 08/2020

Porsche 911 GT3 Cup MR Gen.II

Home

Lookup Tables

Light_Function_left

►

The four LEDs (daytime running lights) of both main headlights of the 911 GT3 Cup MR Gen. II can

light up as an identification feature with a selectable color when the beacon signal is triggered. This

function is particularly useful for night races, as this function makes it easier to identify the vehicle

on the track and in the pit lane. This function can be set separately for the left and right main head-

lights.

►

In addition, the LEDs on the main headlights can be used to display any fault memory entries /

alarms.

►

If the Color ID is to also be displayed when driving in the pit lane when the Pit Speed Limiter is acti-

ve, this can also be set here.

If the preset values are changed, the setup with the new values must

be transferred to the ICD using the

"Send Setup"

button. All data still

stored on the ICD will be lost when the changed setup is transferred!

Carry out a data backup beforehand!

NOTE

Procedure for setting the Color ID / display of the Error Monitor when crossing the timing signal for

the LEDs of the left main headlight:



Enter in Row 0 the Value 1, if the Color ID should be displayed after crossing beacon signal



Enter in Row 0 the Value 2, if the Error Monitor should be displayed after crossing beacon signal

Procedure for setting the Color ID when the Pit Speed Limiter is active.



Enter in Row 1 the Value 1, if the Color ID is to be activated when the Pit Speed Limiter is acti-

vated (in the pitlane)

Open the tab

“Light_Function_left“

The following alarms/errors can be displayed via the LEDs of the headlights when the

beacon signal is crossed. The display then takes place with red glowing LEDs. There is no

differentiation/specification of the alarm / error;

ELECTRICS | Intelligent Color Display (ICD)



Alternator



Crankcase Pressure



Oil Level high



Oil level low



PCU



Fuel Pressure



Oil Pressure



Water Pressure



Gearbox Oil Temperature



Water Temperture



Oil Temperature



Battery Voltage



Water Level

Содержание 911 GT3 Cup MR Gen. II

























































































































Результаты поиска

Содержание 911 GT3 Cup MR Gen. II

Отзывы:

Бренды по названию

Популярные бренды

Porsche 911 GT3 Cup MR Gen. II, Техническое руководство

Результаты поиска

Содержание 911 GT3 Cup MR Gen. II

Отзывы:

Бренды по названию

Популярные бренды