Polaris Light Utility Hauler 6x6 Скачать руководство пользователя страница 96

Страница: 96 / 116

MAINTENANCE AND LUBRICATION

PVT System

PVT Drying

There may be some instances when water is accidently ingested into

the PVT system. Use the following instructions to dry it out before

operating:

1. Remove the drain plug and allow the water to drain. Replace the

drain plug.

2. Start the engine and shift the transmission into neutral. Apply

varying throttle for 10-15 seconds to expel the moisture and air-dry

the belt and clutches. Do not hold the throttle wide open for more

than 10 seconds.

3. Allow the engine RPM to settle to idle speed and shift the

transmission to the lowest available range.

4. Test for belt slippage. If the belt slips, repeat the process.
5. Take the vehicle to your dealer for service as soon as possible.

WARNING

Failure to comply with the instructions in this warning can result

in severe injury or death.
Do not modify any component of the PVT system. Doing so may

reduce its strength so that a failure may occur at a high speed.

The PVT system has been precision balanced. Any modification

will cause the system to be out of balance, creating vibration and

additional loads on components.
The PVT system rotates at high speeds, creating large amounts

of force on clutch components. Extensive engineering and

testing has been conducted to ensure the safety of this product.

However, as the owner, you have the following responsibilities to

make sure this system remains safe:
Always follow all recommended maintenance procedures. See

your dealer as outlined in the owner’s manual.
This PVT system is intended for use on Polaris products only. Do

not install it in any other product.
Always make sure the PVT housing is securely in place during

operation.

Содержание Light Utility Hauler 6x6





















































































































Результаты поиска

Содержание Light Utility Hauler 6x6

Отзывы:

Похожие инструкции для Light Utility Hauler 6x6

Бренды по названию

Популярные бренды

Polaris Light Utility Hauler 6x6, Руководство пользователя

Результаты поиска

Содержание Light Utility Hauler 6x6

Отзывы:

Похожие инструкции для Light Utility Hauler 6x6

Бренды по названию

Популярные бренды