Polaris Light Utility Hauler 6x6 Скачать руководство пользователя страница 70

Страница: 70 / 116

MAINTENANCE AND LUBRICATION

Lubrication Recommendations

NOTE:

Hours are based on 10 mph average.

Maintenance Chart Key

More often under severe use, such as wet or dusty conditions

Grease conforming to NLGI No. 2, such as Conoco Superlube M

or Mobilegrease Special

Use Polaris Premium U-Joint Lube every 500 miles, before long

periods of storage, or after pressure washing or submerging.

Item

Lube Rec.

Method

Frequency*

Brake Fluid

DOT 3 only

Maintain proper level.

See page 36.

As required;

change every

two years or 200

hours

Drive Chains

O-Ring chain lube

or SAE 80/90

Lubricate as often as re-

quired (before each ride in

wet conditions).

As required

Gear Selector Oil

(1)

10 W

Non-detergent Oil

Maintain oil level at the

center of the shift rail. Do

not overfill.

Change every 2

years or 200

hours.

Transmission Oil

(2)

Polaris Premium

Synthetic gearcase

lube

Fill to bottom of the filler

hole.

Change annually

or at 100 hours

Front Prop Shaft

U-joints (3)

Grease

Locate Fittings and

Grease

Every 3 months

or 50 hours

Front Drive Axle

(U-Joint)

Grease

Locate grease fitting and

grease with grease gun.

Every 3 months

or 50 hours

Содержание Light Utility Hauler 6x6





















































































































Результаты поиска

Содержание Light Utility Hauler 6x6

Отзывы:

Polaris Light Utility Hauler 6x6, Руководство пользователя, Страница: 70 / 116

Результаты поиска

Содержание Light Utility Hauler 6x6

Отзывы: