Polaris Light Utility Hauler 6x6 Скачать руководство пользователя страница 43

Страница: 43 / 116

CONTROLS

Recoil Starter

If the battery is weak and cannot start

the engine, use of the recoil starter

(1) will allow vehicle operation until

repairs can be made.
1. Position the vehicle on a level

surface and engage the parking

brake. See page 37.

2. Shift the transmission to neutral.
3. Grasp the recoil starter tightly

and pull slightly until the starter

mechanism engages.

4. Pull the rope abruptly to start the

engine.

Extending the starter rope too far will cause damage to the recoil

assembly. Do not extend the starter rope so far that it stops.
If the starter rope handle is not seated properly, water may enter

the recoil housing and damage components. Make sure the

handle is fully seated on the recoil housing, especially when

traveling in wet areas.

CAUTION

Содержание Light Utility Hauler 6x6





















































































































Результаты поиска

Содержание Light Utility Hauler 6x6

Отзывы:

Похожие инструкции для Light Utility Hauler 6x6

Бренды по названию

Популярные бренды

Polaris Light Utility Hauler 6x6, Руководство пользователя

Результаты поиска

Содержание Light Utility Hauler 6x6

Отзывы:

Похожие инструкции для Light Utility Hauler 6x6

Бренды по названию

Популярные бренды