Polaris Light Utility Hauler 6x6 Скачать руководство пользователя страница 100

Страница: 100 / 116

MAINTENANCE AND LUBRICATION

Lights

Headlight Lamp Replacement

1. Using a small flat-blade screwdriver, push in on the lock tabs

through the two small openings at the front of the headlight pod.

2. Lift the pod slightly while depressing the tabs.
3. Remove the three screws in the back of the headlight pod.
4. Lift the pod cover. Disconnect the speedometer harnesses from the

speedometer. Unplug the indicator light harness and remove the

pod cover.

5. Unplug the headlamp from the wiring harness.
6. Remove the boot and locking collar from the back of the lamp

housing.

7. Grasp the base of the lamp and lift it out.
8. Reverse the previous steps to replace the lamp and reassemble the

pod. Make sure the tab on the lamp locates properly in the

housing.

WARNING

Poor lighting while driving can result in severe injury or death.

Headlight and taillight lenses become dirty during normal operation.

Wash the headlights frequently to maintain lighting quality.
Hot components can cause serious burns to skin. Don’t service the

headlamps until they’ve cooled sufficiently.

Snap pins

into tabs

Position

knob in

slot and

secure in

locking

tabs

Slip o-ring

over pin

Adjustment

Knob Stop

Route plug

over handlebar

Содержание Light Utility Hauler 6x6





















































































































Результаты поиска

Содержание Light Utility Hauler 6x6

Отзывы:

Похожие инструкции для Light Utility Hauler 6x6

Бренды по названию

Популярные бренды

Polaris Light Utility Hauler 6x6, Руководство пользователя

Результаты поиска

Содержание Light Utility Hauler 6x6

Отзывы:

Похожие инструкции для Light Utility Hauler 6x6

Бренды по названию

Популярные бренды