Polaris Light Utility Hauler 6x6 Скачать руководство пользователя страница 71

Страница: 71 / 116

MAINTENANCE AND LUBRICATION

Lubrication Recommendations

Demand 6

Hubs (AWD) (1)

Premium

Hub Lube

Remove set screw in hubs. Ro-

tate wheels to 4:00 position (A). If

lubricant is not visible add more.

Reinstall set screw.

Annually or at

100 hrs

Ball Joint (2)

Grease

Locate zerk on back side of struts

and grease with grease gun.

Every 3 months

or at 50 hrs

Front A-Arm

Pivot Shaft (3)

Grease

Locate zerk on pivot shaft and

grease with grease gun.

Every 3 months

or at 50 hrs

Steering Post

Bushings (4)

Grease

Locate fitting on steering post and

grease with grease gun.

Every 3 months

or at 50 hrs

More often under severe use, such as wet or dusty conditions

Grease conforming to NLGI No. 2, such as Conoco Superlube M or

Mobilegrease Special

Use Polaris Premium U-Joint Lube every 500 miles, before long periods of

storage, or after pressure washing or submerging.

Inner Tie Rod End

Upper

Содержание Light Utility Hauler 6x6





















































































































Результаты поиска

Содержание Light Utility Hauler 6x6

Отзывы:

Polaris Light Utility Hauler 6x6, Руководство пользователя, Страница: 71 / 116

Результаты поиска

Содержание Light Utility Hauler 6x6

Отзывы: